background image

Page 6

CIRCULAR SANDING ACTION

Your sander uses very quick, small circular motions to
remove material. The motion is ideal for producing a fine
finished grain or, when using the scrubbing pad, removing
light rust, paint and other build up from the work surface.

WARNING:

Do not allow familiarity with your sander to make you
careless. Remember that a careless fraction of a second
is sufficient to inflict severe injury.

APPLICATIONS

(USE ONLY FOR THE PURPOSES LISTED BELOW)

Sanding on wood surfaces.

Removing rust from and sanding steel surfaces.

Polishing and scrubbing metal and tile.

CAUTION:

Keep the cord away from the sanding area and position
it so that it will not be caught on lumber, tools, or other
objects during sanding.

KNOW YOUR SANDER

See Figure 1.

Before attempting to use your sander, familiarize yourself
with all operating features and safety requirements.

WARNING:

If any parts are missing do not operate your sander until
the missing parts are replaced. Failure to do so could
result in possible serious injury.

SWITCH

This tool is equipped with a simple switch control. To turn
your sander ON, depress the switch button as shown in
Figure 1. Depress the switch button in the opposite direction
to turn your sander OFF.

VELCRO

®

 PAD

Hook and loop design allows for quick change of sanding
sheets and scrubbing pads and also enables you to reuse
them.

TRIANGULAR SANDING SHEETS

The top two-thirds of each sanding sheet is a detachable
triangle that can be rotated to extend sheet life and promote
even wear.

*VELCRO

® 

is a registered trademark of VELCRO U.S.A. Inc.

Fig. 1

ON/OFF SWITCH

OFF

TRIANGULAR
SANDING SHEET

CONTOURED PALM GRIP

MOTOR HOUSING

BASE PAD

6-FOOT POWER CORD

ON

FEATURES

Summary of Contents for CFS1500













Reviews: