3
English
cordless product in the presence of open flame. An
exploded battery can propel debris and chemicals.If
exposed,flush with water immediately.
■
Do not charge battery tool in a damp or wet
location.
Following this rule will reduce the risk of
electric shock.
■
For best results, your battery tool should be
charged in a location where the temperature is
more than 50°F but less than 100°F. Do not store
outside or in vehicles.
■
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar. If liquid gets into your eyes, flush
them with clean water for at least 10 minutes,
then seek immediate medical attention.
Following
this rule will reduce the risk of serious personal injury.
■
Save these instructions.
Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them these
instructions also to prevent misuse of the product and
possible injury.
FEATURES
V
8
1
e
g
a
tl
o
V
Chuck (mm)
0.8-10 mm
d
e
e
p
s
e
l
b
a
ir
a
V
h
c
ti
w
S
No load speed (drill mode):
0-350/0-1300 min-
1
Max. Torque (Nm)
42.6
Weight - console (KG)
1.27
OPERATION
WARNING:
Do not allow familiarity with products to make
you careless. Remember that a careless fraction
of a second is sufficient to inflict serious injury.
WARNING:
Always wear safety goggles or safety glasses
with side shields when operating products.
Failure to do so could result in objects being
thrown into your eyes, resulting in possible
serious injury.
WARNING:
Do not use any attachments or accessories
not recommended by the manufacturer of this
product. The use of attachments or accessories
not recommended can result in serious personal
injury.
TO INSTALL BATTERY PACK
See Figure 2.
■ Place the rotation selector in center position.
■ Align raised rib on battery pack with groove in drill’s
battery port.
■ Make sure the latches on each side of the battery
packsnap in place and that battery pack is secure
before beginning operation.
TO REMOVE BATTERY PACK
■ Place the rotation selector in center position.
■ Locate latches on side of battery pack and depress
both sides to release battery pack from the drill.
■ Remove battery pack from the drill.
BATTERY PROTECTION FEATURES
Ryobi 18 V lithium-ion batteries are designed with
features that protect the lithium-ion cells and maximize
battery life. Under some operating conditions, these
built-in features may cause the battery and the tool it is
powering to act differently from nickel-cadmium batteries.
During some applications, the battery electronics may
signal the battery to shut down, and cause the tool to
stop running. To reset the battery and tool, release the
trigger and resume normal operation.
NOTE:
To prevent further shut down of the battery, avoid
forcing the tool.
If releasing the trigger does not reset the battery and
tool, the battery pack is depleted. If depleted, the battery
pack will begin charging when placed on the lithium-ion
charger.
WARNING:
Compatible battery
pack (not included)
Compatible charger
(not included)
Lithium-Ion
BPL-1820
BPL-1815
BPL18202PK
RB18L13
RB18L15
RB18L26
RB18L40
RB18LL40
BCL1418
BCS618
BCL14181H
BCL14183H
BCL1418IV*
Nickel
Cadmium
ABP1801G
ABP1802G
ABP-1813
ABP-1815
RB18N15
BCL1418
BCS618
ACR1800G
260022029
BCL14181H
BCL14183H
BCL1418IV*
*
for vehicles with 12V DC outlets
