TO INSTALL BATTERY PACK (fig. 2)
Lock the switch trigger by placing the direction of rotation
selector in the central position.
To install, insert battery pack neck into drill's battery
port, making sure the latches on each side snap into
place and battery pack is secure before beginning
operation.
To remove, locate latches on side of battery pack and
depress both sides to release battery pack from drill.
LCD BATTERY CAPACITY INDICATOR
The display is for guidance only. Deviations are possible
for extreme applications. It will be turned on when the
button is pressed, and will be turned off when the button
is released.
Note:
Indicator is for reference only and can vary
according to ambience and application. For the LCD
display, it so be read when you push the LCD button
and the drill is on; if the drill is off, the display does not
reflect actual battery capacity when you push the LCD
button.
SWITCH (fig. 3)
The drill is started and stopped by depressing and
releasing the switch trigger.
Release the switch trigger to turn the drill OFF.
SWITCH LOCK
The switch trigger can be locked in the OFF position.
This helps to reduce the possibility of accidental starting
when not in use. To lock the switch trigger, place the
direction of rotation selector in the centre position.
When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
Under abusive conditions, liquid may be ejected
from the battery, avoid contact. If contact accidentally
occurs, flush with water. If liquid contact eyes,
additionally seek medical help.
Liquid ejected from
the battery may caused irritation or burns.
SERVICE
Have your power tool serviced by an authorised
service centre using only identical replacement
parts.
This will ensure that the safety of the power
tool is maintained.
MAINTENANCE
Your power tool requires no additional lubrication or
maintenace. There are no user serviceable parts in
your power tool.
Never use water or chemical cleaners to clean your
power tool. Wipe clean with a dry cloth.
Always store your power tool in a dry place.
Keep the motor ventilation slots clean.
If you see some sparks flashing in the ventilation slots,
this is normal and will not damage your power tool.
WORKING HINTS FOR YOUR DRILL
If your power tool becomes too hot, set the speed to
maximum and run no load for 2-3 minutes to cool the
motor.
Always use a magnetic bit holder when using short
screwdriver bits.
Where possible use a pilot hole before drilling a large
diameter hole.
CONTENTS OF BOX
14.4V/18.0V cordless hammer drill, 2 double-ended
bits, 2 battery packs, charger, auxiliary handle.
OPERATING INSTRUCTIONS
CHARGING THE BATTERY PACK (fig. 1)
The battery packs for this tool have been shipped in a
low charge condition to prevent possible problems.
You should, therefore, charge them prior to use.
Note:
Batteries will not reach full charge the first time
they are charged. Allow several cycles (drilling followed
by recharging) for the item to fully charge. The battery
charger should only be used indoors.
Make sure power supply is normal house voltage,
240VoHs, 50Hg, AC only.
Place the battery pack into the charger as indicated.
Align raised rib on battery pack with groove in charger.
Press down on battery pack to make sure contacts
on battery pack engage properly with contacts in charger.
When properly connected, the red light on charger will
turn on.
After normal usage, 1 hour of charging time is required
for the battery to be fully charged.
Note: Normally the red light on the charger will come
on, this indicates charge mode. If the green and yellow
lights come on, remove the battery pack, wait 1 minute
and reinsert battery pack in charger. If the green and
yellow lights continue to remain on an additional 15
minutes, the battery pack is damaged and will not accept
charge. A maximum charge time of 1-1 1/2 hours is
required to recharge a completely discharged battery.
The battery pack will become slightly warm to the touch
while charging. This is normal and does not indicate a problem.
Dot not place the charger in an area of extreme heat
or cold. It will work best at normal room temperature.
When the batteries become fully charged, the green
light on charger will turn on. Unplug the charger from
power supply and remove the battery pack.
LED FUNCTION OF CHARGER
Red
Fast charging mode
Green and yellow
Control charge or defective
Green
Fully charged
RULES FOR SAFE OPERATION
OPERATION
Page 3
