5
English
OPERATION
The green “
SPEED
” LED will light when the switch trigger
is depressed.
The blue “
POWER
” LED indicates that more torque is
required and the drill has automatically shifted into low
speed.
The variable speed switch trigger should be used to
control speed.
DRILLING
See Figure 7.
■
Check the position of rotation selector for the correct
setting (forward or Reverse).
■
Secure the material to be drilled in a vise or with
clamps to keep it from turning as the drill bit rotates.
■
Hold the drill firmly and place the bit at the point to be
drilled.
■
Depress the switch trigger to start the drill.
■
Move the drill bit into the workpiece, applying only
enough pressure to keep the bit cutting. Do not force
the drill or apply side pressure to elongate a hole. Let
the tool do the work.
WARNING
Be prepared for binding at the bit breakthrough.
When these situations occur, drill has a tendency
to grab and kick opposite to the direction of
rotation and could cause loss of control when
breaking through material. If not prepared, this
loss of control can result in possible serious
injury.
■
When drilling hard, smooth surfaces, use a center
punch to mark the desired hole location. This will
prevent the drill bit from slipping off-center as the hole
is started.
■
When drilling metals, use a light oil on the drill bit to
keep it from overheating. The oil will prolong the life
of the bit and increase the drilling action.
■
If the bit jams in the workpiece or if the drill stalls,
stop the tool immediately. Remove the bit from the
workpiece and determine the reason for jamming.
NOTE:
This drill has an electric brake. When the
switch trigger is released, the chuck stops turning.
When the brake is functioning properly, sparks will be
visible through the vent slots on the housing. This is
normal and is the action of the brake.
WOOD DRILLING
For maximum performance, use high speed steel bits for
wood drilling.
■
Begin drilling at a very low speed to prevent the bit
from slipping off the starting point. Increase the speed
as the drill bit bites into the material.
■
When drilling through holes, place a block of wood
behind the workpiece to prevent ragged or splintered
edges on the back side of the hole.
■
When drilling large holes in wood with a spade bit,
the Max admitted bit size is 38mm.
METAL DRILLING
For maximum performance, use high speed steel bits for
metal or steel drilling.
■
Begin drilling at a very low speed to prevent the bit
from slipping off the starting point.
■
Maintain a speed and pressure which allows cutting
without overheating the bit. Applying too much
pressure will:
• Overheat the drill;
• Wear the bearings;
• Bend or burn bits; and
• Produce off-center or irregular-shaped holes.
■
When drilling large holes in metal, start with a small
bit, then finish with a larger bit. Also, lubricate the bit
with oil to improve drilling action and increase bit life.
MAINTENANCE
WARNING:
When servicing, use only identical Ryobi
replacement parts. Use of any other parts may
create a hazard or cause product damage.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING
Do not at any time let brake fluids, gasoline,
petroleum based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may
result in serious personal injury.
Do not abuse power tools. Abusive practices can damage
tool as well as workpiece.
WARNING
Do not attempt to modify this tool or create
accessories not recommended for use with this
tool. Any such alteration or modification is misuse
and could result in a hazardous condition leading
to possible serious personal injury.
9611067192-01.indd 5
9611067192-01.indd 5
5/29/09 11:25:49 AM
5/29/09 11:25:49 AM
