background image

5 - English

 

Protect your lungs. Wear a face or dust mask if the 

operation is dusty. Following this rule will reduce the risk 

of serious personal injury.

 

Protect your hearing. Wear hearing protectors during 

extended periods of operation. Following this rule will 

reduce the risk of serious personal injury.

 

Inspect tool cords periodically and, if damaged, have 

repaired at your nearest authorized service center. 

Constantly stay aware of cord location. Following this 

rule will reduce the risk of electric shock or fire.

 

Check damaged parts. Before further use of the 

tool, a guard or other part that is damaged should 

be carefully checked to determine that it will operate 

properly and perform its intended function. Check for 

alignment of moving parts, binding of moving parts, 

breakage of parts, mounting, and any other conditions 

that may affect its operation. A guard or other part that 

is damaged should be properly repaired or replaced 

by an authorized service center. Following this rule will 

reduce the risk of shock, fire, or serious injury.

SPECIFIC SAFETY RULES

 

Make sure your extension cord is in good condi-

tion. When using an extension cord, be sure to use 

one heavy enough to carry the current your product 

will draw. A wire gauge size (A.W.G.) of at least 14 is 

recommended for an extension cord 50 feet or less 

in length. A cord exceeding 100 feet is not recom-

mended. If in doubt, use the next heavier gauge. The 

smaller the gauge number, the heavier the cord. An 

undersized cord will cause a drop in line voltage resulting 

in loss of power and overheating.

 

Inspect for and remove all nails from lumber before 

using this tool. Following this rule will reduce the risk of 

serious personal injury.

 

If the power supply cord is damaged, it must be 

replaced only by the manufacturer or by an authorized 

service center to avoid risk.

 

Save these instructions. Refer to them frequently and 

use them to instruct others who may use this tool. If you 

loan someone this tool, loan them these instructions also.

CALIFORNIA PROPOSITION 65

WARNING:

This product and some dust created by power sanding, sawing, grinding, drilling, and other construction activities may 
contain chemicals, including lead, known to the State of California to cause cancer, birth defects, or other reproductive 
harm. 

Wash hands after handling.

Some examples of these chemicals are:
•  lead from lead-based paints,
•  crystalline silica from bricks and cement and other masonry products and,
•  arsenic and chromium from chemically treated lumber.
Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your 
exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially 
designed to filter out microscopic particles. 

Summary of Contents for AG403





































Reviews: