RULES FOR SAFE OPERATION
5
•
Always stop the engine and allow it to cool
before filling the fuel tank. Never remove the
cap of the fuel tank, or add fuel, when the
engine is hot. Never operate the unit without
the fuel cap securely in place. Loosen the
fuel tank cap slowly to relieve any pressure in
the tank.
•
Mix and add fuel in a clean, well-ventilated
area outdoors where there are no sparks or
flames. Slowly remove the fuel cap only after
stopping engine. Do not smoke while fueling
or mixing fuel. Wipe up any spilled fuel from
the unit immediately.
•
Avoid creating a source of ignition for spilled
fuel. Do not start the engine until fuel vapors
dissipate.
•
Move the unit at least 30 ft. (9.1 m) from the
fueling source and site before starting the
engine. Do not smoke, keep sparks and
open flames from the area while adding fuel
or operating the unit.
WHILE OPERATING
•
Never start or run the unit inside a closed
room or building. Breathing exhaust fumes
can kill. Operate this unit only in a well
ventilated area outdoors.
•
Wear safety glasses or goggles that are
marked as meeting ANSI Z87.1-1989
standards, and ear/hearing protection when
operating this unit. Wear a face or dust mask
if the operation is dusty. Long sleeve shirts
are recommended.
• Wear heavy, long pants, boots and gloves.
Do not wear loose clothing, jewelry, short
pants, sandals or go barefoot. Secure hair
above shoulder level.
• The cutting attachment shield must always
be in place while operating the unit. Do not
operate unit without both trimming lines
extended, and the proper line installed. Do
not extend the trimming line beyond the
length of the shield.
• This unit has a clutch. The cutting attachment
remains stationary when the engine is idling.
If it does not, have the unit adjusted by an
authorized service technician.
•
Adjust the assist handle to your size to
provide the best grip.
•
Be sure the cutting attachment is not in
contact with anything before starting the unit.
•
Use the unit only in daylight or good artificial
light.
•
Avoid accidental starting. Be in the starting
position whenever pulling the starter rope.
The operator and unit must be in a stable
position while starting. See
Starting/Stopping
Instructions.
•
Use the right tool. Only use this tool for the
purpose intended.
•
Do not overreach. Always keep proper
footing and balance.
•
Always hold the unit with both hands when
operating. Keep a firm grip on both the front
and rear handle or grips.
•
Keep hands, face, and feet at a distance
from all moving parts. Do not touch or try to
stop the cutting attachment when it is
rotating.
•
Do not touch the engine or muffler. These
parts get extremely hot from operation.
When turned off they remain hot for a
short time.
•
Do not operate the engine faster than the
speed needed to cut, trim or edge. Do not
run the engine at high speed when not
cutting.
•
Always stop the engine when cutting is
delayed or when walking from one cutting
location to another.
•
If you strike or become entangled with a
foreign object, stop the engine immediately
and check for damage. Do not operate
before repairing damage. Do not operate the
unit with loose or damaged parts.
•
Stop and switch the engine to off for
maintenance, repair, or for changing the
cutting attachment or other attachments.
•
Use only genuine Ryobi replacement parts
when servicing this unit. These parts are
available from your authorized service
dealer. Do not use parts, accessories or
attachments not authorized by Ryobi for this
unit. Doing so could lead to serious injury to
the user, or damage to the unit, and void
your warranty.
•
Keep unit clean of vegetation and other
materials. They may become lodged
between the cutting attachment and shield.
•
To reduce fire hazard, replace faulty muffler
and spark arrestor, keep the engine and
muffler free from grass, leaves, excessive
grease or carbon build up.
Summary of Contents for 767r
Page 26: ...NOTES 26 ...
