![background image](http://html1.mh-extra.com/html/ryobi/5133003815/5133003815_original-instructions-manual_1504356003.webp)
1
English
|
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
Safety, performance, and dependability have been given
top priority in the design of your percussion drill.
INTENDED USE
The percussion drill is intended to be used only by adults
who have read and understood the instructions and
warnings in this manual and can be considered responsible
for their actions.
The percussion drill can be used for drilling into various
material including wood, metal and plastics using a drill bit
which has a shank diameter of less that 10 mm. It can also
be used in hammer mode for drilling masonry and similar
materials.
Do not use the percussion drill for any other purpose not
described above.
WARNING
Read all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
PERCUSSION DRILL SAFETY WARNINGS
■
Wear ear protectors when impact drilling.
Exposure
to noise can cause hearing loss.
■
Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
■
Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring.
Cutting
accessory contacting a “live” wire may make exposed
metal parts of the power tool “live” and could give the
operator an electric shock.
■
Hold power tool by insulated gripping surfaces,
when performing an operation where the fastener
may contact hidden wiring.
Fasteners contacting a
“live” wire may make exposed metal parts of the power
tool “live” and could give the operator an electric shock.
■
Do not operate on materials (e.g., asbestos) that
present a health hazard.
■
Switch off the product immediately if the bit stalls. Do
not switch on the product again while the bit is stalled,
as doing so could trigger a sudden recoil with a high
reactive force. Determine why the bit stalled and rectify
this, paying heed to the safety instructions.
The possible causes may be:
–
it is tilted in the workpiece
–
it has pierced the workpiece
–
the product is overloaded
■
Sawdust and splinters must not be removed while the
product is running.
■
When working in walls, ceilings, or floors, avoid
electrical cables and gas or water pipes.
■
Secure your workpiece with a clamping device.
■
Ambient temperature range for tool during operation is
between 0
˚
C and 40
˚
C.
■
Ambient temperature range for tool storage is between
0
˚
C and 40
˚
C.
■
The recommended ambient temperature range for the
charging system during charging is between 10
˚
C and
38
˚
C.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING
To reduce the risk of
fi
re, personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack or charger in
fl
uid or allow a
fl
uid to
fl
ow inside them. Corrosive or conductive
fl
uids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
■
Ambient temperature range for battery during use is
between 0
˚
C and 40
˚
C.
Ambient temperature range for battery storage is between
0
˚
C and 20
˚
C.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise and the operator
should pay special attention to avoid the following:
■
Risk of electrocution if electric cables are drilled into –
Always grasp the tool by designated handles. Do not
touch the drill bits
■
Damage to the respiratory system – Wear respiratory
Summary of Contents for 5133003815
