background image

 WARNING 

 

Read all instructions and warnings in this manual before attempting to operate this equipment. 

 

This equipment is designed for outdoor use only. 

 

Be sure to always wear personal protective equipment when operating this equipment. 

 

Improper assembly may be dangerous. Please follow the assembly instructions in this manual. Make sure all parts are 

assembled and hardware is fully tightened before using. Make sure that there are no leaks in the liquid propane cylinder 
connection or lines. 

 

Do not operate the equipment if a gas leak is present. (check for leaks and connections with every use) 

 

Do not attempt to disconnect the gas regulator from the tank or any gas fitting while the equipment is in use. 

 

A dented or rusty liquid propane tank may be hazardous and should be checked by your liquid propane supplier. Do 

not use a liquid propane tank with a damaged valve. 

 Ensure that your propane cylinder is within its expiry date for your local jurisdiction. If the tank has expired it must be 

properly requalified to continue using. 

 Ensure that your propane cylinder is within its expiry date for your local jurisdiction. The manufacturing date is 

stamped on the collar of the tank. If the tank has expired it must be properly requalified.  

 

Do not store spare liquid propane cylinders within 10 feet (3m) of this equipment. 

 

Do not store or use gasoline or other flammable liquids or vapors within 25 feet (8m) of this equipment. 

 

Before servicing, make sure the unit is fully cooled and the liquid propane cylinder is disconnected. 

 

Only genuine RynoWorx replacement parts should be used for any replacements or repairs. Do not attempt to modify 

or alter this product in any way. 

 

Do not attempt to make any repairs to gas carrying, gas burning, igniter components or structural components. Your 

actions, if you fail to follow this warning, may cause a fire, an explosion, or structural failure resulting in serious personal 
injury or death as well as damage to property. 

 

This equipment should only be used with "Direct Fire" hot melt crack sealant. 

 

Failure to follow these instructions could result in fire or explosion which could cause property damage, personal 

injury or death. 

 

 

 

 

 

Summary of Contents for RA-MLT-0013


























Reviews: