RVR Energy Technology TML SF Installation And Operating Instructions Manual Download Page 2

 2 

1.0 INTRODUCTION 

1.1 Reading the Instructions 

Please read and understand these instructions prior to installing the water heater.  

Following installation and commissioning the operation of the heater should be explained to the 
customer and these instructions left with them for future reference. 

 

 

2.0 GUARANTEE 

This water heater is guaranteed for a period of 5 years provided that: 

- It has been installed in accordance with these instructions and all the necessary inlet controls and 
safety valves have been fitted correctly. 

- Any valves or controls are supplied or approved by RVR. 

- The unit has not been tampered with and has been regularly maintained as detailed in these 
instructions. 

- The unit has been used only for heating potable water. 

The unit is NOT guaranteed against damage by frost or due to the build up of scale. 

This guarantee does not affect the statutory rights of the consumer. 

Our policy is that of continuous improvement and development, therefore the right is reserved to 
change specification without notice. 

 

All water heaters must be installed by a competent and qualified person, in accordance with 
relevant clauses of applicable standards and recommendations

 

These include but may not be limited to the following:- 

 

EN12897: 2006 Water Supply—Specification for indirectly heated unvented (closed) 
storage water heaters. 
All relevant Building Regulations 
Local Water Bye Laws 
IEE Wiring Regulations 
Health & Safety legislation 

 

 

Summary of Contents for TML SF















Reviews: