Russound CA 4.4i Instruction Manual Download Page 9

9

PUNCHDOWN TERMINALS

Figure 11

– Punchdown 

Terminal on CAi keypad

The CAi Keypads come with 110 punchdown terminals. These
terminals are quick, easy to install and provide a strong con-
nection. Punchdown terminals require the use of a punch-
down tool. One has been provided with this kit.

Press wires into punchdown terminal with punchdown tool
as shown in Figure 12.

Figure 12

– Punching Down Wires

INSTALLING THE KEYPADS

• The best infrared remote performance is achieved with

the keypad away from any direct sunlight. Also consider
convenience when choosing a location.

• Choose a place that is easily seen from the position where

a person is most likely to be located. 

• Check whether or not you can route the wire to the loca-

tion you have chosen.

• Purchase retro-fit plastic junction boxes (min. 18 cubic

inches) or p-rings and cut in the boxes using a key-hole
saw or sheetrock knife/hand saw.

• If you are installing the optional DSC keypad you will

need to use a double-gang electrical box. If you are
installing both the optional DSC and DAN keypad  you
will need to install a triple-gang electrical box.

• If you feel uncomfortable cutting into your walls and

running wire through the walls, seek help from a profes-
sional installer or an electrician.

• Route the wire to the junction box from the CAi location.

• If using 22 AWG wire, connect each wire to the correct

position 1 thru 8 using the included punchdown tool.
Refer to List 5.

• If using CAT-5 wire, connect each wire to its correspon-

ding color labeled on the punchdown terminal.

• Mount the keypad in the junction box and attach the

Decora© plate.

• The CA-KP2 keypad has source labels for your conven-

ience. Insert the label in the keypad keeping the input
number in sequence with the source selected.

• Repeat the above steps until all keypads are installed.

I

NSTALLING

K

EYPADS

IR

GND

+12V

CH SE

L

SEL3

SEL1

BA

L

VO

L

CAT-5 or 8-conductor

22 AWG wire

Connector on  

CA-KP2 or CA-LCD2

BRO

WN 

GREEN 

ORANGE

BLUE

Punchdown
Tool

CAi-Series manual  10/17/02  11:01 AM  Page 9

Summary of Contents for CA 4.4i

















Reviews: