background image

Copyright ©2020 Russound/FMP Inc. All rights reserved. All trademarks 

are the property of their respective owners. Russound is not responsible 
for typographical errors or omissions. Specifications are subject to change 
without notice. 

The 

Bluetooth®

 word mark and logos are registered trademarks owned by

 

Bluetooth

 SIG, Inc. and any use of such marks by Russond is under license. 

Other trademarks and trade names are those of their respective owners.

Specifications

BTC-1X Remote Transceiver

      Power requirements:  supplied by BTC-1 via CAT-5

    

Frequency:  2,400-2,483.5 MHz

 

CAT-5 connection:   RJ-45 (T568A standard)

 

Dimensions:  70mm x 56mm x 26mm  (W x D x H)

     

Weight:  3.1 ounces

     

Max cable length:  300’ (CAT-5) BTC-1X to BTC-1 

 

   50', (15M) without obstruction| 

BTC-1 Termination box

      Power requirements:   12VDC 300mA

     

CAT-5 connection:   RJ-45 (T568A standard) 

     

Trigger Output:   12VDC 100 mA Max

     

Trigger Input:   12VDC   

     

Audio Connections:   2 RCA

     

Dimensions:   122mm x 51mm x 38mm (W x D x H) 

     

Weight:  7.3 ounces

   

Max cable length:   25’ (RCA cable) BTC-1 to  

  

Amplifier/ 

Receiver

 

  300’ (CAT-5) BTC-1X to BTC-1

Limited Warranty

The Russound BSK-1 is fully guaranteed for two (2) years 

from the date of purchase against all defects in materials and 
workmanship. During this period Russound will replace any 
defective parts and correct any defect in workmanship without 
charge for either parts or labor. For this warranty to apply, the unit 
must be installed and used according to its written instructions. If 
service is necessary, it must be performed by Russound. Russound 
assumes no responsibility for defects resulting from abuse or 
servicing performed by an agency or person not specifically 
authorized in writing by Russound. Damage to or destruction of 
components due to improper use voids the warranty. In these 
cases the repair will be made at the owner’s expense. Accidental 
damage and shipping damage are not considered defects under 
the terms of the warranty. To return for repairs, the unit must 
be shipped to Russound at the owner’s expense, along with a 
Return Authorization number and documentation explaining 
the nature of the service required. Any product returned without 
prior written permission will be returned to sender. Russound 
sells products only through authorized Dealers and Distributors 
to ensure that customers obtain proper support and service. 
Any Russound product purchased from an unauthorized dealer 
or other source, including retailers, mail order sellers and online 
sellers will not be honored or serviced under existing Russound 
warranty policy. Any sale of products by an unauthorized source 
or other manner not authorized by Russound shall void the 
warranty on the applicable product.

To obtain Return Authorization please contact us at:  

[email protected]

Summary of Contents for BSK-1X











Reviews: