background image

·

·

Instruction diagram

Side B

WiFi module connector

Power/Shutter Button

Micro-USB

Sensor connector

WiFi/Mode Switch Button

Side A

LED 1: 

Blue ——WiFi status light

LED 2: 

Green ——Photo mode status light

LED 3: 

Blue —— Video mode status light

LED 4: 

Orange —— OSD Setup status light

LED 5: 

Red —— Power status light, it's always on after being powered

TX

RX

GND

VCC+ (5-15V)
GND
Video
Audio

LED 1
LED 2
LED 3
LED 4
LED 5

Microphone

Buzzer

·

Transmitter connection diagram

User Manual

Preparation

· 

Firmware: CleanFlight (≥2.1.0) / BetaFlight (≥3.2.0)

· 

Any available UART interface on the Flight Controller

1. Connect the RunCam Split 2 with the UART interface of the Flight Controller

2. Make the Flight Controller recognize the RunCam Split 2

For example, we connect the RunCam Split 2 to the UART 3 interface on the Flight 
Controller: connect the Flight Controller to the computer, then open the configurator 
software of the Flight Controller. (Open up the configurator that matches the firmware 
you are running, Betaflight Configurator for Betaflight, Cleanflight Configurator for 
Cleanflight). In the Peripherals column of the line UART3 (on the Ports tab), select 
RunCam Device and click Save And Reboot.

3.  Instructions of the functions of the camera and assigning transmitter 
     channels to them

In the Flight Controller Configurator, navigate to the Modes tab. There are new 
CAMERA WI-FI, CAMERA POWER and CAMERA CHANGE modes

.

·  

CAMERA WI-FI: turn on/off the WIFI of the camera. When in the OSD of the camera, this 

    is used to confirm your selection.

·  

CAMERA POWER: start/stop the video. When in the OSD of the camera, this is used to 

    move to the next menu item.

·  

CAMERA CHANGE MODE: switch among the three modes, video, photo and OSD 

    setting mode. When in the OSD of the camera, this will exit the menu.

Assign any available channel to the function you need, for example:

·  

Assign the AUX1 to the CAMERA WI-FI, range 1900-2100

·  

Assign the AUX2 to the CAMERA POWER, range 1900-2100

·  

Assign the AUX3 to the CAMERA CHANGE MODE, range 1900-2100

4. Assign the channel to the switch of the controller

Please choose your Model on the controller, then access to the MIXER interface and 
assign the channel to the switch of the controller. Take opentx 2.2.0 for example, assign 
the channels CH5, CH6 and CH7 to SA, SB and SD respectively.

5. Test

Power the Flight Controller and the RunCam Split 2

·  

Set the SA to the bottom, the camera starts/stops the video

·  

Set the SB to the bottom, the camera turns on/off the WIFI

·  

Set the SD to the bottom, the camera switches among the three modes: video, photo 

    and OSD setting mode

·

Flight Controller Set

GND

GND

TX

TX

RX

RX

FC

UART Interface

·

App(Android | iOS)

     Search 'RunCam App' on Google Play/Apple Store, or download on our website:

     https://www.runcam.com/download/runcamsplit2

     

Default SSID: 

RCSplit_ ****** (* for letters or numbers)

     

Default WiFi password: 

1234567890

www.runcam.com

·

Parameter

Field of View (FOV)

Video Resolution

Video File Format

Image Resolution

TV Mode

Real-Time Audio Output

Interface

Max Micro SD Card Supported

WiFi Module

Dimensions

Power Input

Working Current

Weight

FPV FOV 130°/Recording FOV 165°

1080@60fps/1080@30fps/720@60fps

MOV

2 Megapixels

NTSC (720*480)/PAL (720*576) Switchable

Yes

Micro USB / UART

64G(need Class 6 or above, 

recommend Class 10/UHS-I/UHS-II/UHS-III)

Support (Removable)

PCB 38*38mm/Lens Module 22*20mm

DC 5-15V / DC 5V(USB)

650mA @5V/270mA @12V

21g/23g (Plus WiFi Module)

Note: 

Recording automatically after turing on by default, with the V1.0 firmware, under 

            the video status, short press WIFI/MODE SWITCH button to pause/start the 
            recording. With the V1.1 and later firmware, under the video status, short press 
            WIFI/MODE SWITCH button to stop the recording and turn on the WIFI; Under the 
            standby mode, the function of the WIFI/MODE SWITCH button doesn't change.

·

Basic Camera Operation

Powering On/Off

WiFi On/Off

Mode Switching

Video Mode

Photo Mode

OSD Setup Mode

Forced Shutdown

Reset

Long press the Power/Shutter button

Short press the WiFi/Mode Switch button

After powering on, long press the WiFi/Mode Switch button to cycle 
through the three modes: Video/Photos/OSD settings.

Camera Status Light: 

Blue (LED 3)

• Press the Power/Shutter button to start/stop recording.

Camera Status Light: 

Green (LED 2)

• Press the Power/Shutter button to capture photos.

Camera Status Light: 

Orange (LED 4)

• Press the Power/Shutter button to move to a setting. 
• Press the WiFi/Mode Switch button to select. 
• Long press the WiFi/Mode Switch button to exit the menu.

Simultaneously press the Power/Shutter button and 
WiFi/Mode Switch button.

In standby mode, press the WiFi/Mode Switch button three times in rapid 
succession (within 2 seconds). When resetting is complete, the status 
light (orange) blicks twice, and the camera automatically shuts down.

Warning:

 Please push upward the black locking arm before you unplug the lens cable in 

                    case the connector is destroyed. And Golden fingers on ends of the lens cable 
                    should face to the opposite of each other. For more details about how to 
                    connect the lens cable properly, you may refer to: 

https://goo.gl/PoGg1T

Warning:

 USB port only supports DC 5V

·

MicroSD Card

     Capacity up to 64GB; Please use high speed cards(Class10/UHS-I/UHS-II).

Please push the metal piece a little bit up with one hand like showed in above step 1 
and then press the SD card(step 2) with another hand to let the card pop out.

2

1

·

Lens module connection diagram

OPEN

2

1

LOCK

1

2

·

Installation Diagram

Warning:

 

USB port only supports DC 5V

USB

DC 5V

·

Technical Support

      Please visit

https://support.runcam.com

5V

GND

GND

Video

Power in

GND

PDB

Methos Two: 

connect by the TV-out and power USB cable

Method One (Recommended): 

connect by the soldering pads

5-15V

5-15V

GND

Video

Audio

Power in

GND

PDB

Video Transmitter

Video Transmitter

RunCam

 

Device

 

and

 

click

 

Save

 

And

 

Reboot.

3.

I

Ins

t

truc

t

t

i

ions o

f

f

t

t

h

he

f

func

t

t

i

ions o

f

f

t

t

h

he camera an

d

d ass

i

ign

i

ing

t

transm

i

i

t

t

t

ter

  

Assign the AUX3 to the CAMERA CHANGE MODE, range 1900 2100

4

A

A

ss

ii

gn

tth

h

e c

h

h

anne

ll tt

o

tth

h

e s

wiitt

c

h

h

of

f tth

h

e con

tt

ro

llll

er

Reviews: