background image

 

Miknetum MPR 500 

15 

13302  FINK 

 Antisept A  Alcohol-based disin-

fectant 

n

eu

tr

a

100 

RT 

d

a

ily

 

13304  FINK 

 Antisept E  Alcohol-based disin-

fectant 

100 

RT 

17107  FT 107 DES 

Disinfection 

2.0 

 5.0 

15 

 30 

20 

 40 

18803  FINK 

 Alu-Rei-

niger 

Acid foam cleaner 

a

ci

d

 

2.0 

 5.0 

 15 

20 

 50 

O

n

ce

 in

 2

 w

ee

ks

 

17043  FT 43 SR 

Acid foam cleaner 

1.0 

 5.0 

 15 

20 

 50 

18550  FINK 

 FC Power-

foam S1 

Acid foam cleaner 

1.0 

 2.0 

 20 

20 

 50 

17310  Ökoron® 10 

Disinfectant, acid 

0.3 

 1.0 

20 

 30 

 70 

17307  Ökoron® 7S 

Disinfectant, acid 

0.5 

 2.0 

 20 

 60 

17312  Ökoron® 12 

Acid disinfection 

0.5 

 3.0 

Cold 

17313  Ökoron® 13 

Acid disinfection, 
foamable 

0.1 

 1.0 

45 

17900  Ökoron® SR 

Ecological cleaner 

a

ci

d

 

1.0 

 5.0 

15 

 20 

20 

 55 

d

a

ily

 

*)  

13308, FINK 

 

Antisept G 

Because of customer-specific application prohibitions, QAC-containing prod-
ucts are sometimes not used since the IFS standard must be met. Possible 
alternative products would be, for example, FT 107 DES.

 

Supplier: 

FINK TEC GmbH, Oberster Kamp 23, 59069 Hamm, Germany 
Tel. +49 2385-730 / [email protected] / www.finktec.com 

 

4.3

 

Cleaning procedure 

Please refer to the short instructions supplied with your machine for 
carrying out the cleaning procedure.  
 
Cleaning preparations: 
 

 

To ensure optimum cleaning, some components of the machine 
must be removed. 

 

Remove the mixing arm and the tumbling arm from the drum! 

 

Simply pull off the stripper rubber at the tumbling arm from the 
outside to the inside. 

 

Pull the lid seal off the inside of the lid! 

 

Remove the intake filter at the upper lid edge out of the bracket.  

Summary of Contents for MPR 500






















Reviews: