background image

 

Miknetum MPR 500 

11 

3

 

Operating instructions 

Please refer to the short instructions supplied with your machine for 
the operation of your Miknetum.  
 

 

Also observe Chapter 1 Safety instructions! 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Make sure that you are connected to the right machine 
with your tablet PC!  

Depending on the application programs, the drum is 
moved automatically. While the program is running, no 
person may stand within the working range of the ma-
chine (front distance at least 1.2 m over the entire ma-
chine width). 

Before the drum moves automatically, a 5 second alarm 
(horn) sounds. 

If the power fails when a user program is being executed 
the machine will react as follows when the power supply 
is reinstated: it will start up again automatically and the 
program will continue from that point at which it was in-
terrupted by the power failure. The startup warning 
(horn) will sound before this restart.  

In its respective life cycle phases (transport, commission-
ing, setup, operation, cleaning, decommissioning, 
care/maintenance, dismantling/disposal), this machine is 
designed for single person operation!  

When using this machine, no other person may be present 
near the machine. The exception (2-man operation): 

 

Installation and removal of lid 

 

Installation and removal of lid holder 

 

Installation and removal of tumbling arm 

 

Installation and removal of mixing arm 

 

Installation and removal of standard trolley support 

 

Installation and removal of protective gearbox cover 

 

Transport of machine and machine parts 

 

Maintenance work inside the drum 

Summary of Contents for MPR 500






















Reviews: