manualshive.com logo in svg

Ruckus Wireless T504, Installation Manual

Share
Download
Ruckus Wireless T504 Installation Manual Download Page 30

Installing the T504

Deploying the T504

T504 Strand Mount Concurrent AP with Integrated CM Installation Guide, 800-70610-001 Rev A

31

Configuring the Downstream Frequency

The 

Configure Status 

page allows you to set the downstream frequency for the 

cable modem. Configuring the downstream frequency enables the device to quickly 
obtain a direct frequency lock with the CMTS upon bootup and helps to save several 
minutes of scanning for an available downstream frequency from the CMTS.

1

Log into the 

Status 

page as described in 

Logging Into the CM Web Interface 

from the T504 Ethernet Port

 or 

Logging Into the CM Web Interface using a 

Dynamic IP Address

.

2

Click 

Configure

 in the left sidebar. The CM web interface displays the 

Configure 

Status

 page. See 

Figure 11

.

Figure 11.  Configure Status page

3

In the 

Configure DS Frequency 

text box, enter the downstream frequency (in 

Hertz) that you want the cable modem to use to connect to the CMTS when it 
boots up. 

4

Click 

Set Values and Reboot 

to have the cable modem save your changes and 

reboot.

DRAFT

Summary of Contents for T504

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands