background image

 

 

iii 

SAFETY SUGGESTIONS 

 
Read Instructions.

 Read all safety and operating instructions before operating the unit. 

Retain Instructions. 

Keep the safety and operating instructions for future reference. 

Heed Warnings.

 Adhere to all warnings on the unit and in the operating instructions. 

Follow Instructions.

 Follow operating instructions and instructions for use. 

Heat.

 Keep the unit away from heat sources such as radiators, heat registers, stoves, etc., 

including amplifiers that produce heat. 

Power Sources.

 Connect the unit only to a power supply of the type described in the 

operating instructions, or as marked on the unit. 

Power Cord Protection.

 Route power supply cords so that they are not likely to be walked 

on or pinched by items placed on or against them, paying particular attention to the cords at 
plugs, at convenient receptacles, and at the point at which they exit from the unit. 

Water and Moisture.

 Do not use the unit near water—for example, near a sink, in a wet 

basement, near a swimming pool, near an open window, etc. 

Object and Liquid Entry.

 Do not allow objects to fall or liquids to be spilled into the 

enclosure through openings. 

Servicing.

 Do not attempt any service beyond that described in the operating instructions. 

Refer all other service needs to qualified service personnel. 

Damage Requiring Service.

 The unit should be serviced by qualified service personnel 

when: 

!

 

The power supply cord or the plug has been damaged. 

!

 

Objects have fallen or liquid has been spilled into the unit. 

!

 

The unit has been exposed to rain. 

!

 

The unit does not appear to operate normally or exhibits a marked change in 
performance. 

!

 

The unit has been dropped, or the enclosure damaged. 

 
 
 
 

  Limited Warranty and Disclaimer 

WARNING ! 

TO REDUCE THE RISK OF FIRE OR ELECTRIC 
SHOCK, DO NOT EXPOSE THE UNIT TO RAIN OR 
MOISTURE.

 

Summary of Contents for RP-6































Reviews: