background image

Page 

1

 of 

6

 

 

3245 Corridor Drive, Eastvale, CA 91752 

 

800.769.2414 

 951.360.1600  

 951.360.7500 (Fax

 
 

                                                       OWNER’S MANUAL 

INSTRUCTIONS, INSTALLATION, OPERATION, MAINTENANCE 

RHPE & RTGE SERIES (ELECTRIC COUNTERTOPS)   

 

 

 

 

 

RETAIN THIS MANUAL FOR FUTURE REFERENCES. 

 
IMPORTANT.  Installing, Operating and Service Personnel: 

Safe and satisfactory operation of your equipment depends to a great extent on its proper installation. Installation 

must conform with local codes, or in the absence of local codes, to the 

National

 

Electrical Code, ANSI/NFPA-70

 

(latest edition). In Canada, Installation should conform to 

Canadian Electrical Code CSA-C22.2.

 

Electrical wiring from the electric meter, main control box or service outlet to appliance must be electrically 

grounded in accordance with local codes, or in the absence of local codes, with the 

National Electrical Code 

ANSI/NFPA- 70 

(latest edition) or the 

Canadian Electrical Code CSA-C22.2. 

Installation of the equipment should be performed by qualified, certified, licensed and/or authorized personnel 

who are familiar with and experienced in state/local installation codes.  

Operation of the equipment should be performed by qualified or authorized personnel who have read this manual 

and are familiar with the functions of the equipment.  

Service of the equipment should be performed by qualified personnel who are knowledgeable with ROYAL 

RANGE OF CALIFORNIA, INC.  

SHIPPING DAMAGE: 

 

The equipment is inspected and crated carefully by skilled personnel before leaving the factory. The transportation 

company assumes full responsibility for safe delivery upon acceptance of this equipment. Upon receipt of shipment, 
immediately  unpack  and  check  for  possible  shipping  damage.  If  the  equipment  is  found  to  be  damaged,  save  the 
packaging material and contact the carrier immediately.  

RATING PLATE: 

 

The rating plate is located on the right side of the appliance. Information on this plate includes the model, serial 

number, power input, ampere draw and clearances. This data is essential for proper identification when communicating 
with the factory regarding a unit, requesting parts or information. 

ROYAL  RANGE  COOKING  APPLIANCES  MUST  BE  CONNECTED  ONLY  TO  THE  POWER  INPUT 
IDENTIFIED ON THE RATING PLATE. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

July 2017 

Email: [email protected] 

 www.royalranges.com 

FOR YOUR SAFETY 

DO NOT STORE OR USE GASOLINE OR 
OTHER FLAMMABLE VAPORS OR 
LIQUIDS IN THE VICINITY OF THIS OR 
ANY OTHER APPLIANCE. 

WARNING 

Improper installation, adjustment, alteration, 
service or maintenance can cause property 
damage, injury or death. Read the installation, 
operating and maintenance instructions thoroughly 
before installing or servicing this equipment.  

Summary of Contents for RHPE-12-1







Reviews: