Royal RG1000 Owner'S Manual Download Page 16 | Manualshive

Page: 16 / 26

Royal RG1000 Owner'S Manual Download Page 16

Numbers

When the grill is connected to AC power, the model number
and software version of the control are displayed momentarily.

Temperature

In cook mode and smoke mode, the grill temperature is
displayed in 5 degree (Fahrenheit) increments.

Flashing Temperature

In cook mode, the displayed temperature fl ashes if the grill
temperature is below 150 degrees.

In smoke mode, the displayed temperature fl ashes if the grill
temperature is below 110 degrees.

Flashing Dots

The igniter is on.

“P0” - “P15”

When the cook control switch is set to the smoke position,
the smoke setting is displayed for 3 seconds.

If you adjust the smoke control switch while in smoke
mode, the smoke setting is displayed for 3 seconds.

If you adjust the smoke control switch while in the cook
mode, the idle fuel feed rate setting is displayed for 3 seconds.

Flashing “ErH”

The grill temperature exceeded 615 degrees.

Flashing “ErP”

The cook control switch was not in the off position when
the grill was connected to AC power.

RG-DIGITAL CONTROL UNDERSTANDING THE DISPLAY

«
...
14
15
16
17
18
...
»

Summary of Contents for RG1000



























Reviews:

No comments