![background image](http://html1.mh-extra.com/html/royal/34-205-04/34-205-04_original-operating-instructions_1494083021.webp)
Always fasten the ejector flap carefully. The flap flips
back to the “Closed” position by the tension springs!
Always ensure that a safe distance (provided by the
long handles) is maintained between the user and
the housing. Be especially careful when scarifying
and changing direction on slopes and inclines.
Maintain a solid footing and wear sturdy, non-slip
footwear and long trousers. Always scarify along the
incline (not up and down).
For safety reasons, the scarifier may not be used to
scarify inclines whose gradient exceeds 15 degrees.
Use special caution when backing up and pulling the
scarifier (tripping hazard)!
9. Tips for proper working
It is recommended that you overlap scarifying paths
a little.
Try to scarify in straight lines for a nice, clean look.
Insodoing, the aeration swaths should always
overlap each other by a few centimeters in order to
avoid bare strips.
As soon as grass clippings start to trail the scarifier, it
is time to empty the grass basket.
Important! Before taking off the grass basket,
switch off the motor and wait until the roller has
come to a stop.
To remove the grass basket, lift up the ejector flap
with one hand, while unhooking the basket with the
other.
How frequently you should scarify your lawn is
determined primarily by the speed at which the grass
grows and the hardness of the soil.
Keep the underside of the equipment clean and
remove soil and grass build-up. Deposits make it
more difficult to start the aerator and decrease the
quality of the scarifying.
Always scarify along inclines (not up and down).
Switch off the motor before doing any checks on the
roller.
Important!
The roller rotates for a few seconds after the motor is
switched off. Never attempt to stop the roller. In the
event that the rotating roller strikes an object,
immediately switch off the equipment and wait for the
roller to come to a complete stop. Then inspect the
condition of the roller. Replace any parts that are
damaged (see section 7).
Lay the power cable on the ground in loops in front of
the power outlet. Scarify away from the power outlet
and cable, making sure that the power cable always
trails in the already scarified grass so that the
equipment does not travel over the cable.
10. Maintenance, care and storage
Maintenance and cleaning work on the equipment as
well as removal of the safety devices may only be
performed when the motor is switched off and the
power cable has been pulled.
Replace a worn or damaged roller immediately.
Caution!
Do not touch tools while they are running.
Do not clean the equipment with running water and
particularly not with a pressure hose.
Ensure that all mounting components (i.e. screws,
nuts etc.) are always tightened so that the equipment
can be safely operated at all times.
Store the equipment in a dry room. In order to ensure
that you enjoy your scarifier for many years to come,
all screwed parts, as well as the wheels and axles,
should be cleaned and lubricated.
Keeping your scarifier in good condition not only
ensures a long lifespan and high performance, but
also enables the equipment to thoroughly scarify
your grass with minimal effort. For best results, clean
the equipment with a brush or rag. Do not use any
solvents to remove dirt.
At the end of the season, perform a general
inspection of the equipment and remove any
deposits which may have accumulated.
At the start of each season, ensure that you check
the condition of the equipment. If repairs are
necessary, please contact one of our customer
service centers (see address on warranty certificate).
11. Ordering spare parts
The following information should be given when
ordering replacement parts:
앬
Model/type of the equipment
앬
Art. No. of the equipment
앬
ID No. of the equipment
앬
Part number of the required spare part
For our latest prices and information please go to
www.isc-gmbh.info
21
GB
Anleitung_N-RVL_1200_SPK7:_ 26.10.2009 15:25 Uhr Seite 21
Summary of Contents for 34.205.04
Page 3: ...3 5 3 4 6 7 A B C D E 7 14 6 4 13 14 Anleitung_N RVL_1200_SPK7 _ 26 10 2009 15 25 Uhr Seite 3 ...
Page 4: ...4 8 10 9 11 12 12 12 12 13 10 Anleitung_N RVL_1200_SPK7 _ 26 10 2009 15 25 Uhr Seite 4 ...
Page 6: ...6 20 Anleitung_N RVL_1200_SPK7 _ 26 10 2009 15 25 Uhr Seite 6 ...
Page 44: ...EH 10 2009 01 Anleitung_N RVL_1200_SPK7 _ 26 10 2009 15 26 Uhr Seite 44 ...