background image

RSL-2702S

3

 1.  INTRODUCTION

2.  SAFETY PRECAUTIONS

Failure to comply with any of the following safety procedures could result in serious injury.  

Please read the instructions carefully and keep for future reference.  
1. Only a licensed electrician should install wiring and outlet for the laminator.
2.  Ensure the unit is plugged into a properly grounded outlet with the correct voltage.
3.  Keep hands and clothing (i.e. Neckties) away from rollers.The rollers have pinch points 

that can trap body parts or clothing and cause serious injury.

4. Keep flammable and wet objects away from the machine.
5. Place machine on a level surface.
6. Avoid excessive sunlight, humidity and extreme temperatures.
7.  Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving and/

or repairing.

8. Keep out of reach of children.
9.  Only Royal Sovereign authorized maintenance and service technicians should make 

repairs.

10.  Do not attempt to laminate items that exceed total recommended material thickness 

for the unit

11. When cleaning the machine, don't use flammable sprays or materials.
12.  Do not touch the rollers when they are hot.
13. Do not place foreign objects inside the machine.
14.  Do not cover the surface of the machine until the machine has completely cooled.

Thank you for choosing a Royal Sovereign laminator. It has been designed and 

manufactured to provide years of continuous service. For complete operating and 

maintenance information please read this manual thoroughly.  Upon receipt of your 

laminator, please inspect the box, the machine and all other contents for shipping 

damage. Damage should be brought to the immediate attention of the delivering carrier 

(See page 3 for list of shipment elements).   

Summary of Contents for RSL- 2702S





















Reviews: