Royal Sovereign RSC-1650CL, Owner'S Manual, Page: 7 / 7

RSC-1650CL
12 11
14. SPECIFICATIONS
Description RSC-1650CL
Power supply AC 220~240V 50/60Hz
Power consumption 100W
Max laminating width 1650mm / 65"
Film thickness 50~250 mic / 1~7mil
Max laminating speed 3m/min / 9.9ft/min
Ready time Not applicable
Heating method None
Driving motor DC geared
Max Temperature control
Not applicable
Speed control 9 settings
Transport type 2 Roller
Film core size Auto grip (2",3")
Cross cutter No
Hot lamination No
Cold lamination Yes
Mounting thickness 7mm / 0.3"
Take up system No
Reverse Yes
Remote control No
Foot pedal Yes
Unit dimensions 1950
?/X?gW.h
?V/Xf?W.Yh V/X?eW.Y?h
?V/X?W.Yhe V/T.Y?he ?S@Uhf
W.R/X?he ?W.Y?V/Xhe
W.Y?eV/X?h ?W.Yf?V/Xh ?.Y?gV/h
550
?/X?gW.h
?V/Xf?W.Yh V/X?eW.Y?h
?V/X?W.Yhe V/T.Y?he ?S@Uhf
W.R/X?he ?W.Y?V/Xhe
W.Y?eV/X?h ?W.Yf?V/Xh ?.Y?gV/h
1040 (mm)
(w x d x h) 77"
?/X?gW.h
?V/Xf?W.Yh V/X?eW.Y?h ?V/X?W.Yhe
V/T.Y?he ?S@Uhf
W.R/X?he ?W.Y?V/Xhe W.Y?eV/X?h
?W.Yf?V/Xh ?.Y?gV/h
21.6"
?/X?gW.h
?V/Xf?W.Yh V/X?eW.Y?h ?V/X?W.Yhe
V/T.Y?he ?S@Uhf
W.R/X?he ?W.Y?V/Xhe W.Y?eV/X?h
?W.Yf?V/Xh ?.Y?gV/h
41"
Unit weight 145kg / 319lbs
Carton dimensions 2178
?/X?gW.h ?V/Xf?W.Yh
V/X?eW.Y?h ?V/X?W.Yhe V/T.Y?he
?S@Uhf W.R/X?he
?W.Y?V/Xhe W.Y?eV/X?h ?W.Yf?V/Xh
?.Y?gV/h
814
?/X?gW.h ?V/Xf?W.Yh
V/X?eW.Y?h ?V/X?W.Yhe V/T.Y?he
?S@Uhf W.R/X?he
?W.Y?V/Xhe W.Y?eV/X?h ?W.Yf?V/Xh
?.Y?gV/h
710(mm)
(w x d x h) 85.7"
?/X?gW.h ?V/Xf?W.Yh
V/X?eW.Y?h ?V/X?W.Yhe V/T.Y?he
?S@Uhf W.R/X?he
?W.Y?V/Xhe W.Y?eV/X?h ?W.Yf?V/Xh
?.Y?gV/h
32"
?/X?gW.h ?V/Xf?W.Yh
V/X?eW.Y?h ?V/X?W.Yhe V/T.Y?he
?S@Uhf W.R/X?he
?W.Y?V/Xhe W.Y?eV/X?h ?W.Yf?V/Xh
?.Y?gV/h
28"
Gross Weight 166kg / 365.2lbs
12. MAINTENANCE
13. TROUBLESHOOTING
Cleaning the Body of the laminator
1.To clean the machine body, dampen a cloth with water only and gently wipe the
machine clean.
Removing Adhesive Build Up
1. Remove the film from the laminator.
2. Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the
Teflon (metal) and silicone rollers.
Lubrication
1. Drive chain and sprockets should be lubricated with either a light coat of gear lube or
heavy grease (lithium grease) after 6 months or 1000 hours of operation, whichever
comes first.
Note: Rub firmly but do not scrub the rollers vigorously as this may scratch the surface.
Do not use sharp metal objects, steel wool, or abrasives, as these
may also damage the rollers.
Symptom Cause Possible Solution
Machine will not turn
on:
a. Power plug is not plugged in.
b. Power switch is in “0” (Off) position.
c. Tripped circuit breaker.
d. Blown main power fuse.
a. Plug the power cord into appropriate
outlet.
b. Put the power switch to the “I” (On)
position.
c. Reset the circuit breaker.
d. Replace the fuse.
There is power, but the
rollers are not turning
after the “RUN” button
is pressed:
a. Emergency switch(es) is (are) engaged.
b. Paper guide is not installed correctly.
c. Blown motor fuse.
a. Disengage the emergency switch(es).
b. Properly install the paper guide so that
the micro switch is activated.
d. Replace the motor fuse.
The unit is not heating
up:
a. Did not raise the temperature. a. Raise the temperature.
Curled lamination:
a. Upward curl.
b. Downward curl. a. Loosen the top roll film tension.
b. Loosen the bottom roll film tension.