background image

- 17 - 

Problem

Cause

Remedy

Engine does not start

1. Spark plug wire disconnected.

2. Ignition switch set to OFF.

3. Fuel tank empty.

4. Stale or improperly mixed fuel 

mixture.

5. Dir ty air 

Ƥ

lter/oil 

Ƥ

lter.

6. Incorrectly gapped or dirty spark 

plug.

7. Primer bulb not depressed 

adequately.

8. Flooded engine.

1. Reconnect wire.

2. Set switch to ON.

3. Add fuel.

4. Empty the tank and 

Ƥ

ll with fresh fuel 

mixture.

5. Clean or replace 

Ƥ

lter.

 

6. Clean or adjust the gap.

7. Slowly and fully depress the primer 

bulb 10 times.

8. Squeeze the throttle and pull the 

starter rope with the choke lever in the 

operating position.

Engine does not run 

constantly at no load

1. Dirty air/oil 

Ƥ

lter.

2

. Stale or improperly mixed fuel 

mixture.

3. Incorrectly gapped or dirty spark 

plug.

1. Clean or replace 

Ƥ

lter.

2. Empty the tank and 

Ƥ

ll with fresh fuel 

mixture.

3. Clean or adjust the gap.

Engine does not idle

Improper carburetor adjustment

  Adjust ac cording to the manual or turn to 

an authorized service dealer for help.

Engine does not

accelerate

1. Dirty air/oil 

Ƥ

lter.

2. Throttle wire disconne

cted. 

3. Defective throttle control lever.

4. Incorrectly gapped or dirty spark 

plug.

5. Improper carburet or adjustment

1. Clean or replace 

Ƥ

lter.

2. Reconnect throttle wire.

3. Replace the throttle control lever.

4. Clean or adjust the gap.

5.  Adjust according to the manual or 

turn to an authorized service dealer for 

help.

TROUBLE-SHOOTING

TROUBLE-SHOOTING

Summary of Contents for XT133























Reviews: