Roto-Mix 274-12 Page 11 Operation And Parts Manual Download

Page: 11 / 69

PREPARING TRACTOR FOR TRAILER MIXER

POSITIONING DRAWBAR

IMPORTANT: Drive components can be damaged from

excessive speed. Under no circumstances
should a feed mixer equipped with 540
RPM be operated by a tractor with 1000
RPM PTO.

Feed mixers are available with either 540 or 1000 RPM
driveline. Match tractor PTO with the feed mixer
driveline.

IMPORTANT: To prevent driveline damage, adjust

tractor drawbar to recommended setting.
Disengage tractor PTO before turning.

Remove clevis if equipped. Turn offset drawbar down.

Adjust drawbar length:

PTO SPEED

DIMENSION (A)

540 RPM

14 inches (356 mm)

1000 RPM

16 inches (406 mm)

ADJUST TRAILER HITCH CLEVIS

Mixer should be approximately level when attached to
tractor.

Adjust clevis by changing hole location on tongue.

Hitch Pin Size --- 1” x 7”

SAFETY

READ BEFORE

YOU FEED

Summary of Contents for 274-12






































































Search results

Summary of Contents for 274-12

Reviews:

Related manuals for 274-12

Brands by name

Popular brands

Roto-Mix 274-12, Operation And Parts Manual

Search results

Summary of Contents for 274-12

Reviews:

Related manuals for 274-12

Brands by name

Popular brands