background image

USER MANUAL

 

ENGLISH

rothaudio.co.uk  

|  11

7.  PAIR Indicator

 

This indicator flashes during the pairing process between the 
BAR1 and Subwoofer. After the link between the BAR1 and 
Subwoofer is established, this indicator will turn off.

8.  POWER Button

 

Plug the power cord into the AC outlet. The BAR1 goes to the 
standby mode. Press this button to turn the BAR1 on. The 
POWER indicator will illuminate to indicate the BAR1 is on. 
The BAR1 will remain on as long as an input signal is active. 
If the input becomes inactive the BAR1 will change to standby 
mode to conserve power. To completely turn off the BAR1, 
press this button again.

9.  SURROUND Button

 

This button is used to select either the FX SURROUND mode 
or the STEREO mode.

10.  MUTE Button

 

Press this button when you want to activate the audio mute. 
Press it again to deactivate the mute function. Pressing the 
VOLUME buttons will also deactivate the mute function.

11.  MAIN VOLUME Buttons

 

Press the + or - button to adjust the main volume up or down 
respectively.

12.  SUBWOOFER VOLUME Buttons

 

Press the + or - button to adjust the Subwoofer volume up or 
down respectively. The Subwoofer volume sets the balance 
of the Subwoofer with the BAR1. So the output level of the 
Subwoofer is adjusted by both the main volume and the 
Subwoofer volume.

13.  INPUT SELECTOR Button

 

Press this button to select INPUT 1, INPUT 2, or INPUT 3.

14.  PAIRING Button

 

This is used to recover the wireless connection between the 
BAR1 and the Subwoofer. Press and hold this button at least 
3 seconds until the PAIR indicator on the front panel starts 
flashing. Then press the PAIRING button on the rear panel of 
the Subwoofer. The two units should link back up.

15.  INPUT 3

 

Connection type - 3.5 mm mini stereo. If your TV has a 
headphone output, this is a primary input to use by using the 
supplied 3.5 mm mini stereo cable.

16.  INPUT 2

 

Connection Type - RCA. Use this input to connect with your 
external devices (Blu-ray Players, DVD Players, CD Players, 
MP3 Players, or Home Video Game Systems).

17.  INPUT 1

 

Connection Type - RCA. If your TV does not have a headphone 
output, use this input to connect with the set-top-box by using 
the supplied RCA cable.

18.  PAIR Indicator

 

Upon confirming the PAIR indicator on the front panel of the 
BAR1 flashes, press the PAIRING button on this panel. It will 
turn on when the wireless connection is recovered.

19.  PAIRING Button

 

This is used to recover the wireless connection between the 
BAR1 and the Subwoofer. Upon confirming the PAIR indicator 
on the front panel of the BAR1 flashes, Press this button. The 
two units should link back up.

Remote Control

POWER

Press this button to 

turn the BAR1 on 

or off.   

SURROUND   

This button is used to 

select either  the FX 

SURROUND mode or 

the  STEREO mode.  

SUB 

VOLUME  

Press the  + or - 

button to adjust  

the Subwoofer 

volume up or down  

respectively.  

MUTE 

Press this button when 
you want  to activate 
the audio mute. Press 
it  again to deactivate 
the mute  function. 

INPUT 
SELECTOR 

Press this button 
to select  INPUT 1, 
INPUT 2, or INPUT 3. 

MAIN 
VOLUME 

Press the  + or - 
button to adjust  the 
main volume up or 
down  respectively.  

Roth SoundBar Manual EH.indd   11

7/3/11   11:20:13

Summary of Contents for BAR 1

















Reviews: