background image

English

4

Installation Tips

1.

Removing and installing front panel 

• Removal method 

1) Slide until the 2 stoppers click into place.
2) Open the front panel forward and undo the string.
3) Remove the front panel.

• Installation method 

1) Attach the front grille and front panel after pulling the string 

around them.

2) Close the front panel and slide until the stoppers click outside.

2.

Removing and installing front grille 

• Removal method

1) Open the front panel.
2) Remove the 4 screws and remove the front grille while pulling 

it forward (3 tabs).

• Installation method

1) Secure the front grille with the 4 installation screws (3 tabs).
2) Return the front panel to the original position.

3.

How to set the different addresses

When two indoor units are installed in one room, the two 
wireless remote controllers can be set for different addresses.

1) Remove the front grille.
2) Lift the sensor securing plate and remove the front metal plate cover. 
3) Remove connectors 5P, 6P, and 7P.
4) Remove the electrical wiring box (1 screw).
5) Remove the thermistor.
6) Remove the side metal plate cover (7 tabs).
7) Cut the address jumper (JA) on the printed circuit board.
8) Cut the address jumper in the remote controller. 

Front panel

Casing

3 tabs

Front grille

Remove 4 screws.

Remove 
front grille

Open the front panel.

3) Connector 6P

5) Thermistor

3) Connector 5P

3) Connector 7P

4) Remove 1 screw.

Jumper ADDRESS

EXIST

1

CUT

2

JA

ADDRESS

EXIST

1

CUT

2

JA

2) Front metal plate cover

6) Side metal plate cover

2) Sensor 

securing 
plate

Jumper

Summary of Contents for rfwxv15aveb

















Reviews: