28
RSP-1576MKII Surround Sound Processor
Specifications
Audio
Total Harmonic Distortion
0.0006% (Analog Bypass)
0.003% (Digital Input)
Intermodulation Distortion
(60 Hz : 7 kHz, 4:1)
< 0.005%
Frequency Response
Phono Input
20 Hz - 20k Hz, ± 0.5 dB
Analog Bypass
10 Hz - 100k Hz, ± 1 dB
Digital Input
20 Hz - 20k Hz, ± 0.5 dB
Signal to Noise Ratio
(A-weighted)
Analog Bypass
112 dB
Digital Input
112 dB
Input Sensitivity/Impedance
Phono Level
3.5 mV / 47k ohms
Line Level
270 mV / 100k ohms
Balance Level
500 mV / 100k ohms
Preamp Output Level
Line Level
1.0 V
Channel Separation
(at 10k Hz
)
> 75 dB
Digital Audio
LPCM (up to 192kHz, 24-bit)
Dolby
®
Surround,
Dolby
®
TrueHD,
Dolby
®
ATMOS,
DTS-HD Master Audio,
DTS
X
Dirac Live Full
Video
Input Resolutions
480i/576i, 480p/576p, 720p,
1080i, 1080p, 1080p 24Hz,
3D, 4K, UHD, 4K 60Hz, 4K HDR10
Output Resolution
480i/576i, 480p/576p, 720p
1080i, 1080p, 1080p 24Hz,
3D, 4K, UHD, 4K 60Hz, 4K HDR10
Color Space Support
sRGB, YCbCr 4:2:2, YCbCr 4:4:4
Deep Color Support
24-bit, 30-bit, 36-bit
HDMI Inputs/Outputs
7 inputs supporting HDCP 2.2, HDMI2.0b
2 outputs supporting HDCP 2.2, HDMI2.0b
Audio Return Channel
General
Power Consumption
60 watts
< 0.5 watt (standby)
Power Requirements
(AC
)
120 volts, 60Hz
230 volts, 50Hz
BTU
114 BTU/h
Dimension
(W x H x D)
431 x 144 x 348 mm
17 x 5
2
/
3
x 13
5
/
7
in
Front Panel Height
3U / 132.6 mm / 5
1
/
4
in
Weight
8.8 kg / 19.4 lbs
All specifications are accurate at the time of printing.
Rotel reserves the right to make improvements without notice.
Rotel and the Rotel Hifi logo are registered trademarks of The Rotel Co., Ltd. Tokyo, Japan.
Use of the Made for Apple badge means that an accessory has been
designed to connect specifically to the Apple product(s) identified in the
badge and has been certified by the developer to meet Apple performance
standards. Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards
.
Apple, Apple TV, Apple Watch, iPad, iPad Air, iPad Pro, iPhone, and Lightning
are trademarks of Apple Inc., registered in the U.S. and other countries. tvOS
is a trademark of Apple Inc.
No Video Output
•
Make sure that the TV monitor is connected properly and check the
input assignments.
•
Check the source input and TV output resolution are compatible. A 4K
source can only be sent to a 4K monitor.
•
HDMI cables must be 5 meters or less in length.
•
If watching 3D sources, make sure the display is 3D enabled.
Video and Audio do not match.
•
Check that the proper video source is selected for each input.
•
Check that the group delay (lip-sync) setting is not mis-adjusted.
Clicking or popping sounds when switching inputs
•
The unit uses relay switching to preserve maximum sound quality. The
mechanical clicking of the relays is normal.
•
Switching between HDMI sources may cause delays as HDMI two way
communications “handshake” must be established between the source
and display. The time required for the handshake varies depending
on the attached equipment.
Controls do not operate
•
Make sure that fresh batteries are installed in the remote.
•
Make sure that the IR sensor on the front panel is not blocked. Aim the
remote control at the sensor.
•
Make sure the sensor is not receiving strong IR light (sunlight, halogen
lighting, etc.).
•
Unplug the unit from the AC outlet, wait 30 seconds, and plug it
back to reset.
•
Confirm the IR Codeset set in the remote control and RSP-1576MKII
are matched to either Codeset 1 or Codeset 2.
