Rotary SL230RA-PE Installation Instructions Manual Download Page 15 | Manualshive

Page: 15 / 30

Rotary SL230RA-PE Installation Instructions Manual Download Page 15

Installation Instructions ROTARY inground lifts SL230/SL235/SL2

50 • Release: 11/2013 • Page 15

Fig. 15 Middle piece of synchronization mechanism

6.4 Arrange cylinders

Drive up cylinders to appr. 80 cm. Control both cylinders by using a spirit level if they are perpendicular. Where
appropriate, underlay the basic executions with suitable metal strips. For this purpose, remove the screws of the
basic execution and hoist it approx. 10 cm. After underlaying the metal strips screw together the basic executions
and control again if it is perpendicular. If necessary repeat this process several times.

With the models SL235BR and SL250BR-RA we strongly recommend to mount

the two

cylinders slightly outwards! We recommend about 2-3 cm outwards at the top of the cylinders when lifted
completely.

6.5 Installation of the cover and sealing

Remove  the  plastic  foil  from  the  surface  of  the  cover.  Put  the  cover  carefully  between  the  basic  guides  and  take
care that the cover bears on completely.

Then  seal  the  lift  between  the  cassettes´  frame  and  the  basic  guides  resp.  the  cover  using  the  profiled  rubber.
Additionally tighten the profiled rubbers at their ends using silicone.

«
...
13
14
15
16
17
...
»

Summary of Contents for SL230RA-PE































Reviews:

No comments