Rotary 300 Series Operation & Maintenance Manual Download Page 10

Page: 10 / 12

MANUAL LOWERING

MANUAL LOWERING

If the car lift cannot perform lowering operations because of power supply interruption, faulty hydraulic valves

or electric trouble in the system, the lift can be lowered manually. For manual lowering operation (emergency),

perform the following:

• Make sure there are no obstacles blocking the lowering phase; remember that the car lift may not be lifted

again to remove possible obstacles.

• Disconnect main power supply.

• Remove manual lowering cap.

Note: Manual lowering (emergency) operations should be preformed by authorized personnel specially trained

for operating the car lift only.

• Loosen the manual operators (OM) (A1-B1)

1/2 turn.

• Emergency lowering has started; speed can be increased or decreased according to the opening of screws.

OM-A2

Manual

Lowering

Cap

Manual

Lowering

Cap

OM-B2

Summary of Contents for 300 Series













Search results

Summary of Contents for 300 Series

Reviews:

Related manuals for 300 Series

Brands by name

Popular brands

Rotary 300 Series, Operation & Maintenance Manual

Search results

Summary of Contents for 300 Series

Reviews:

Related manuals for 300 Series

Brands by name

Popular brands