background image

How to Use the Reader 

18 

AY-M26 Installation and Configuration Manual 

5.2

 

Manual LED and Buzzer Control 

LED and buzzer behavior depend upon the reader firmware. For 
example, three beeps on reset and successful configuration, or one 

short beep and a flashing LED upon card transmission. However, it is 
possible that the host control panel, to which the reader is connected, 

may control the LED, the buzzer, or both. This depends upon 

manipulation of the LED/buzzer control input, and only if these 
options are enabled by the reader configurations. 
These settings can be overridden using the brown LED/buzzer control 
wire: 

 

LED/buzzer control wire is left open: 

 

LED and buzzer behave naturally based on firmware 
preferences 

 

LED/buzzer control wire is connected to ground: 

 

If the LED control is enabled, the LED turns green 

 

If the buzzer control is enabled, the buzzer continuously 

buzzes 

 

If both LED and buzzer control are enabled, the led turns 

green and buzzer contentiously operated. 

Use the LED/buzzer control wire to determine the behavior of the LED 

and buzzer directly from the access control software. 

 

LED and buzzer control function can be only programmed by 

Configuration card. They cannot be programmed using the 
reader keypad. 

5.3

 

Optical Back Tamper 

The AY-M26 includes an optical back tampering mechanism that 
detects all attempts to dismantle the unit or remove it from the wall. 
The status of the tamper mechanism is indicated by the purple tamper 
control wire. 
When the back tamper optical sensor is in “darkness” status, the 

internal tamper output transistor is pulled to low. 

Summary of Contents for AY-M26






















Reviews: