background image

SMA-8018 

••

 Serial Monitoring Amplifier – User’s Manual

Ross Part Number:  

DM-8018-02

Document Issue:  

2

Printing Date:  March 15, 2000.  Printed in Canada.

The information contained in this guide is subject to change without notice or
obligation.

Copyright

© 2000 Ross Video Limited.  All rights reserved.

Contents of this publication may not be reproduced in any form without the written
permission of Ross Video Limited.  Reproduction or reverse engineering of
copyrighted software is prohibited.

Notice

The material in this guide is furnished for informational use only.  It is subject to
change without notice and should not be construed as commitment by Ross Video
Limited.  Ross Video Limited assumes no responsibility or liability for errors or
inaccuracies that may appear in this manual.

Trademarks

 is a registered trademark of Ross Video Limited.

Ross, ROSS, ROSS

 and RossGear are registered trademarks of Ross

Video Limited.

All other product names and any registered and unregistered
trademarks mentioned in this guide are used for identification purposes
only and remain the exclusive property of their respective owners.

Company Address

Ross Video Limited

Ross Video Incorporated

8 John Street

P.O. Box 880

Iroquois, Ontario, K0E 1K0

Ogdensburg, New York

Canada

USA 13669-0880

General Business Office:

(+1) 613 

 652 

 4886

Fax:

(+1) 613 

 652 

 4425

Customer Service:

(+1) 613 

 652 

 4886

E-mail (Customer Support):

[email protected]

E-mail (General Information):

[email protected]

Website:

http://www.rossvideo.com

After hours emergency:

(+1) 613 

 652 

 4886, ext. 333

Summary of Contents for SMA-8018











Reviews: