background image

79. Press the two push‑buttons on the ‘Tailgate 

lowering’ control panel simultaneously until the 
tailgate engages locks and then release the push‑
buttons.

4543-OM1-R-GB-G1

4580-OM1-R-GB-G1

•  The engine speed should increase.

•  The ejection plate should  should retract into 

the body for 1‑2 seconds before tailgate starts 
to lower.

•  Tailgate should rotate smoothly downwards 

about the hinge pins until it engages face of 
body, then lower into locks.

•  Vehicle reversing’ alarm should sound until the 

tailgate engages locks when it should silence.

2748-DS005-OL1-D-GB-G2

0

No errors

0

No errors

0

No errors

Hyd Oil Temp

0

No errors

0

No errors

09:00:00

Hyd_Oil_Pressure

0

No errors

0

No errors

0

No errors

Hyd Oil Temp

0

No errors

0

No errors

32 

o

C

01.06.2013 09:00:00

Hyd_Oil_Pressure

2 Bar

80. If the vehicle is fitted with a waste container lifting 

device carry out the  daily safety checks described 

in ‘3.2 Daily safety checks ‑ waste container lifting 
device (when fitted)’ on page 3‑22.

81.  If the vehicle is fitted with footboards carry out the  

daily safety checks described in ‘3.3 Daily safety 
checks ‑ footboard (when fitted)’ on page 3‑24.

82. Check level of oil in hydraulic oil tank and top up 

if required (see ‘4.1 To check hydraulic system oil 
level’ on page 4‑3).

3.2 

daily safety checks - waste 

container lifting device (when 
fitted)

Caution 

If one or more footboards is fitted, 
lower footboard(s) before operating 
waste container lifting device.

The following daily safety checks must be carried 

out on the waste container lifting device mechanism, 

in addition to checks specified in the chassis 
manufacturer’s service information and section 3.1 
Daily safety checks ‑ refuse collection body before the 
vehicle commences service.
The following checks assume that the aforementioned 
daily safety checks have been carried out, the engine is 

running and the refuse collection bodywork operating 
system is in the ‘Body system run mode’ with the 

compaction mechanism and lifting device controls 

energised.
1.  If the vehicle is fitted with foot boards, lower them.
2.  If waste container lifting device is fitted with DIN 

arms, open the DIN arms.

•  Check that they open freely and are not seized.

•  Check that springs hold DIN arms in open 

position.

•  Check that the lock plates in the hooks move 

freely and are not seized.

4614-OM1-R-GB-G1

wARNING: 
KeeP CLeAR OF THe MOVING MeCHANISM.

dAILY CHeCKS

3‑22

OM1R-SM-GB01R

3

Summary of Contents for Olympus Mini















































































































Reviews: