manualshive.com logo in svg

ROSITEK MPP2, User Manual And Troubleshooting, Page: 14 / 15

Share
Download
ROSITEK MPP2 User Manual And Troubleshooting Download Page 14

PAGE 13

Rositek Technologies 

www.rositek.com

© 2021 Rositek

All rights reserved

Email: [email protected]

USER GUIDE AND TROUBLESHOOTING

How to Replace the Bottle Jack?

The instruction is applicable to bottle jack styled heat press machine that needs to replace the jack 

step by step:

1. Loose the bolts under the base and on the collar if includes.

2. Ask someone to help you lift up the heated plates.

3. Remove the bottle jack.

4. After loading the replacement. If the replacement offers a thread, please pre-install the screws 

and nuts (do not tightened it).

5. Lift the bottle jack till dual heated platens touched, and then adjust the dual heating plates to 

align with each other.

6. Lift up the bottom heated plate harder, tighten all bolts at the end.

Tips: 

We tighten the original jack on the base to ensure that the upper and bottom heating plates are 

aligned. You have no need to drill and tap a thread to a new replacement,but make sure center 

mounted for alignment to the base.

 TROUBLESHOOTING

Bottle Jack Does Not Hold Pressure After Receiving It, How to Fix It?

Step1 - Please check release valve and ensure the release valve closed tightly.

Step2 - The pressure is still not well maintained after step1, please remove the red plastic cap 

located at the bottom of jack (next to the release valve), and rotate no more than 30 degrees 

clockwise to increase the pressure of the jack.

Tips:

 

This is normal if you are able to continue applying pressure (You have to press down handle very 

harder), it means that the rated pressure of the jack has been exceeded (overload condition), 

and sounds air escaping. 

If you can’t fix it after trying, please share a video at [email protected] for further support.

Summary of Contents for MPP2
















Reviews:

No comments