Rosemount 3107 Reference Manual Download Page 27 | Manualshive

Page: 27 / 148

background image

17

Reference Manual

00809-0200-4841, Rev BA

Section 3: Installation

December 2014

Section 3: Installation

To connect the transmitter:

1.

Make sure that the power supply is disconnected.

2.

Connect the cable wires (see

Figure 3-8 on page 17

),

taking note of the restricted

voltage of 12 to 30 Vdc for

hazardous area (classified location) applications

.

Note



Other devices may reset if connecting the transmitter to a multi-drop system while the
loop is powered. De-energize loop to avoid devices being reset.



Make sure that the instruments in the loop are installed according to intrinsically-safe
field wiring practices and control drawings, when applicable.

Figure 3-8. Wiring diagram

A. Black: 0 Vdc
B. Red: 12 to 40 Vdc (for non-hazardous area) or 12 to 30 Vdc from protective barrier (for hazardous area)
C. Non-hazardous area: connect cable screen to standard ground (earth) or

hazardous area: connect cable screen to intrinsically safe ground (earth)

D. Remote temperature sensor (3108 only)

3.4.2

Remote temperature sensor (on 3108 only)

The factory-fitted remote temperature sensor on the 3108 may be installed in a hazardous area
without the need for any additional protection or barriers.

Note



See also

“Positioning of the remote temperature sensor (3108 only)” on page 14

.

A

C

B

D

«
...
25
26
27
28
29
...
»

Summary of Contents for 3107





















































































































































Reviews:

No comments

Related manuals for 3107

Pacemark PM4410

Brand: Oki Pages: 2

Brand: Datavideo Pages: 16

Brand: OHIO SEMITRONICS Pages: 12

AIR-EAGLE FM2 43-1000-SSB-R1/8-DC

Brand: BWI Eagle Pages: 2

Brand: Continental Refrigerator Pages: 3

Brand: YEONHWA M TECH Pages: 19

Brand: Zeggo Pages: 8

Efector 600 TAD081

Brand: IFM Electronic Pages: 25

Brand: Witura Pages: 18

Brand: Richelieu Pages: 2

Brand: FS Pages: 20

Brand: Amprobe Pages: 59

Lafayette TRUCKER

Brand: Marcucci Pages: 34

Brand: RFM Pages: 5

Brand: Barrett Pages: 246

Brand: Nagano Keiki Pages: 8

Brand: EDOBE Pages: 32

Brand: TEXAS RANGER Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands