manualshive.com logo in svg

Rosemount 1495, Installation & Operation Manual

Share
Download
Rosemount 1495 Installation & Operation Manual Download Page 17

Reference Manual 

00809-0100-4792, Rev CA
August 2010

3-5

Rosemount 1495, 1496

SAFETY MESSAGES

Instructions and procedures in this section may require special precautions to 
ensure the safety of the personnel performing the operations. Please refer to 
the following safety messages before performing any operation in this section.

INSTALLATION 

INSTRUCTIONS
Step 1: Determine the 

Proper Placement

Determine the proper placement by ensuring adequate straight run. See 
Appendix B: Recommended Installation Requirements.

Step 2: Determine the 

Proper Orientation

To determine the proper orientation, see “Installation Configuration” on 
page 2-2.

Step 3: Weld the Flange 

Union

To weld the flange union, see “Step 3: Weld the Flange Union” on page 4-2.

Failure to follow these installation guidelines could result in death or serious injury:

* Make sure only qualified personnel perform the installation.

Personal hazard! To prevent injury, remove pressure and drain pipe assembly before 
installing or removing orifice plate.

If the process fluid is caustic or otherwise hazardous, the procedure outlined here must be 
modified as required to prevent death or serious injury to personnel.

Summary of Contents for 1495







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands