manualshive.com logo in svg

Rosemount 1199, Reference Manual

Share
Download
Rosemount 1199 Reference Manual Download Page 25

Reference Manual 

00809-0100-4002, Rev BB
November 2012

3-5

Rosemount 1199

Figure 3-5. EFW Extended 
Flush Flanged Remote Seal 2-D 
Diagram

Figure 3-6. EFW Flush Flanged 
Remote Seal 3-D Diagram

Bolt Torquing

When connecting the process and mating flange, the bolts should be torqued 
to the applicable flange requirements. Required torque is a function of the 
gasket material and surface treatment of the bolts and nuts which are 
customer supplied.

Flushing Connection 
Ring Installation 
(Flanged cont.)

The flanged type seals are available with an optional flushing connection ring. 

Gasket Installation 
(Flanged cont.)

When connecting the remote seal, gasket, and flushing connection ring make 
sure the gasket is properly aligned on the gasket sealing surface. Failure to 
properly install the gasket may cause process leaks, which can result in death 
or serious injury.

Instrument Connection

Extension Length

Upper Housing

Diaphragm

One-Piece Design

Two-Piece Design

Diaphragm

Process Flange

Diaphragm

Process 
Flange

Summary of Contents for 1199



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands