manualshive.com logo in svg

Rosemount 1199, Reference Manual

Share
Download
Rosemount 1199 Reference Manual Download Page 22

Reference Manual

00809-0100-4002, Rev BB

November 2012

Rosemount 1199

3-2

The protective cover should remain on the seal until the moment before 
installation. Try to avoid touching the diaphragm with fingers or objects and 
refrain from setting the diaphragm side of the seal down on a hard surface. 
Even minor dents or scratches in the diaphragm material may impair the 
performance of the seal system assembly.

When installing remote seal systems which employ a gasket or a gasket and 
flushing connection ring, make sure the gasket is aligned properly on the 
gasket sealing surface. The user is responsible to ensure the gasket used 
does not exceed the temperature limits of the process. Failure to properly 
install the gasket may cause process leaks, which can result in death or 
serious injury.

In addition, make sure the gasket does not press down upon the diaphragm 
face. Anything pressing on the diaphragm will be read by the transmitter as 
pressure. A misaligned gasket may cause a false reading. 

Failing to recognize incorrect materials during installation may cause process 
leaks, which can result in damage to the diaphragm seal system or death 
and/or serious injury to personnel. Proper wetted material is required for 
specific process materials. Please contact your Emerson Process 
Management representative on questions regarding proper process-wetted 
materials.

GASKETS

The diaphragm gasket is supplied when the lower housing or flushing 
connection is provided. The default gaskets are listed below, based on seal 
type. The process gasket must be supplied by the end user. Tantalum 
diaphragms are not supplied with default gasket, so a gasket option must be 
selected when applicable. 

Table 3-1.  Gasket Materials

Seal Type

Gaskets

FFW

ThermoTork TN-9000 

FCW

No gasket is supplied

FUW

No gasket is supplied

FVW

No gasket is supplied

RCW

C-4401 

RFW

C-4401 

FTW

C-4401 

PFW

ThermoTork TN-9000 

PCW

No gasket is supplied

WSP

C-4401

Summary of Contents for 1199



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands