
Safety
ROSCO - A LeeBoy Company
RB48 BROOM
2.8
SAFETY
7. Tighten the fuel tank cap securely. If cap is
lost, replace it only with the original manufacturer's
approved cap. A non-approved cap without proper
venting may result in pressurization of the tank.
8. Use the correct fuel grade for the operating
season. Refer to the Hydraulic Fluid chart in the
Maintenance section of this manual.
BATTERY
1. Keep all sparks and flames away from
batteries. Fumes from the battery's
electrolyte solution is extremely
explosive. Acid propelled by an
explosion can cause blindness if it
comes in contact with eyes.
2. Wear safety glasses when working near
batteries. If you come in contact with battery
electrolyte solution wash it off immediately.
3. Do not tip batteries more than 45 degrees to
avoid spilling electrolyte solution and causing a
chemical burn.
4. To avoid injury from spark or short circuit,
disconnect battery ground cable before
servicing any part of the electrical system. Failure
to do so can result in electrical shock or burn.
5. Use jumper cables only in recommended
manner. Improper use can result in battery
explosion or unexpected broom motion. Refer to
the Engine and Battery pages of the Maintenance
section of this manual.
SAFETY DECALS
1. Keep safety decals and signs clean and
legible at all times.
2. Become familiar with the content and
position of each safety decal. Refer to the Safety
Decal section in this manual for position and part
number.
3. Replace safety decals and signs that are
missing or have become illegible.
4. When replacing parts, be sure to check that
any safety decals that were on the original part
are also on the new part.
5. Obtain safety decals or signs from your
Authorized ROSCO Dealer/Distributor.
DECAL INSTALLATION
1. Be sure that the installation area is clean
and dry. Use hot soapy water and dry the area
thoroughly before installing decals.
2. Decide on the exact position by taking
measurements and test fitting before you remove
the backing paper.
3. For decals with no top protection paper,
decide on the decal location and remove the
smallest portion of the split backing paper.
4. Align the decal over the specified area and
carefully press the small portion with the exposed
adhesive backing into place.
5. Slowly peel back the remaining paper and
carefully smooth the remaining portion of the decal
in place.
6. Small air pockets can be pierced with a pin
and smoothed out using the piece of decal
backing paper.
7. If the decal has a protective top paper, use
hot soapy water on the surface to which the decal
is being applied. Leave wet. After deciding on the
location, remove the backing paper and soak the
decal in clean soapy water before application.
This will help prevent air bubbles in the finished
decal.
8. Smooth the decal into place with a sponge
and check for air bubbles. Small air pockets may
be pierced with a pin and smoothed out. When the
decal is completely smoothed out, carefully
remove the top paper.
Summary of Contents for RB48
