background image

10-00328 REV C 

II 

WARRANTY 

 

Remote Ocean Systems, Inc (hereinafter called “

ROS

”) warrants its products as slated below to 

the conditions specified. 
 

ROS

 warrants this product, when operated under normal conditions, to be free from defects in 

material  or  workmanship  for  a  period  of  two  years  from  the  date  of  purchase  provided  that 
inspection by 

ROS

 discloses that such defects developed under normal and proper use.  

ROS

 

products  repaired  or  replaced  pursuant  to  this  warranty  shall  be  warranted  for  the  unexpired 
portion of the warranty applying to the original product.  The liability of 

ROS

 under this warranty 

shall exist subject to the following conditions: 
 

(a) 

ROS

 is properly notified of such defects by Purchaser, and the defective product 

is returned to 

ROS

, transportation charges paid by Purchaser. 

 

(b) 

ROS

 shall be released from all obligations under its warranty in the event repairs 

or modifications are made by persons not authorized by 

ROS

 

(c) 

Representations  and  warranties  made  by  any  person,  including  distributors  and 
representatives of 

ROS

, which are inconsistent or in conflict with the terms of this 

warranty, shall not be binding upon 

ROS

 unless reduced to writing and approved 

by  an  officer  of 

ROS

.   

ROS

  shall  in  no  event  be  liable  for  other  direct,  special, 

incidental, consequential, indirect or penal charges. 

 

(d) 

This warranty shall be governed by the laws of the State of California. 

 
In the event the defect is determined to be within the terms of this warranty, then 

ROS

 agrees to 

repair and/or replace (at 

ROS

’s discretion) the product of defective portion at no charge to the 

Purchaser.  This warranty does not apply to expendable items or to normal wear and tear and is 
conditional upon performance of normal preventative maintenance procedures. 
 
Our  commitment to quality and customer  service directs  us to constantly strive to improve our 
products.    The  materials  and  specifications  presented  in  our  manuals  and  data  sheets  are 
correct and accurate to the best of our knowledge, and are presented in good faith.  However, 
the information is not guaranteed and is subject to change without notice. 
 

LIMITATION OF REMEDIES 

 
Purchaser assumes all risk and liability for results obtained in any installation, operation, or use 
of the p

roduct.  Purchaser’s sole remedy for any breach of warranty by vendor shall be limited to 

the  “express  remedies”  set  forth  above.    Otherwise,  in  no  event  shall  vendor,  its  agents,  or 
employees be liable to the original purchaser  or third party for any consequential or  incidental 
damages  or  expenses  of  any  nature  arising  directly  out  of  or  in  connection  with  the  use  of 
vendor  products.    Even  if  vendor  has  been  advised  of  the  possibility  of  such  damages  or 
expenses.  In any event, unless otherwise contrary to state law, vendor liability under this limited 
warranty shall not exceed the purchase price of the product. 

Summary of Contents for Q-LED II














Reviews: