background image

Page | 2  

TF 200.01.0040_ENG 

Table of Contents 

 

1.

 

Symbols used in this manual ............................................................................................................. 3

 

2.

 

General safety ..................................................................................................................................... 3

 

3.

 

General requirements ......................................................................................................................... 5

 

3.1

 

Product information ............................................................................................................... 5

 

3.2

 

Product description ............................................................................................................... 5

 

3.3

 

Intended use ......................................................................................................................... 5

 

3.4

 

Intended population .............................................................................................................. 6

 

3.5

 

Intended operator.................................................................................................................. 6

 

3.6

 

Basic safety .......................................................................................................................... 6

 

4.

 

Charging the battery ........................................................................................................................... 6

 

4.1

 

Recharging procedure ........................................................................................................... 7

 

4.2

 

Connection procedure ........................................................................................................... 7

 

5.

 

Mounting instructions......................................................................................................................... 7

 

5.1

 

Electrical component diagram ............................................................................................... 8

 

5.2

 

Mounting the control.............................................................................................................. 8

 

5.3

 

Testing.................................................................................................................................. 9

 

5.3.1

 

Before testing the frame ................................................................................................ 9

 

5.3.2

 

Testing the frame .......................................................................................................... 9

 

5.3.3

 

Testing the safety-strip .................................................................................................. 9

 

6.

 

Troubleshooting.................................................................................................................................10

 

7.

 

Cleaning .............................................................................................................................................10

 

8.

 

Maintenance .......................................................................................................................................11

 

8.1

 

Periodic maintenance of the frame .......................................................................................11

 

8.2

 

Periodic maintenance of the battery .....................................................................................11

 

9.

 

Component part list ...........................................................................................................................11

 

9.1

 

Accessories, component part list ..........................................................................................12

 

10.

 

Environmental protection ..................................................................................................................13

 

10.1

 

Packaging, transport, and storage ....................................................................................13

 

10.1.1

 

Packaging ....................................................................................................................13

 

10.1.2

 

Transport .....................................................................................................................13

 

10.1.3

 

Storage ........................................................................................................................13

 

 

 

Summary of Contents for 50-41020














Reviews: