Ronstan ANDERSEN Compact Motor 58ST, Product Manual

Page: 4 / 22

PRODUCT MANUAL
58-62ST Above Deck Compact Motor
™
4
A4
A7
A1
A2
A5
A13
A11 A9
Exploded View
58-62ST Above Deck Compact Motor™ 12V/24V
2
1
3
4
Mounting Dimension Template
Andersen Winches
Compact Motor ™ Above Deck
Winches, Size 52, 58, 62 ST
Scale 1:1
Page size A3
Product No. RA2052005100 RA2052005200 RA2052015100 RA2052015200
RA2058015100 RA2058015200 RA2062015100 RA2062015200
IMPORTANT
This template document has been created at 1:1 scale. It is critical that
it is printed at 1:1 scale. Check any printed/reproduced copies match
the dimensions indicated at 1:1 scale prior to use.
E
D
8 holes:
First Ø10.5mm (13/32"). 11mm deep
then Ø6.5mm (9/32") through.
Use ISO 4762-A4 M6 bolts.
76mm + deck thickness
+ thread below deck.
8
7
6
5
36.8 4
5 .1
36.8
Ø 250
B A
Ø 230
DC
9
0
20
Lowest point Only required for motors
ordered with optional
secondary push button
(Drain port)
C
45°
Dimensions in mm unless otherwise indicated
Mounting Dimension Template Part No. RD100456 - Rev.2
HOLE DIAMETER PURPOSE
A 30mm Motor terminal RED positive (+)
B 30mm Motor terminal RED negative (-)
C 15mm Drain port
D 25mm Push button control cable & thermal sensor
E 20mm Optional secondary push button
ART No: RD100456
PRODUCT MANUAL
Compact Motor ™
Below Deck
Electric Winch
58-62ST
FOR USE WITH:
Compact Motor™ Electric Winches
RA2058014100 RA2062014100
RA2058014200 RA2062014200
Compact Motor™ Conversion Kits
RA2058214100 RA2062214100
RA2058214200 RA2062214200
Winch Versions:
58ST (≥V.2.0) 62ST (≥V.4.0)
Your Winch Version No. ___________________________________________________________
Your Motor Serial No. _______________________________________________________________
710207-Rev.1
Push Button - E1, Two Speed & Three Speed Electric Winches
Scale 1:1
Page size A4 (210mmW x 297mmH)
Product No’s RA582000, RA582010, RA582020
Method A
Blue shaded areas of template
Drill a Ø19mm (3/4”) hole at the centre of the push button
location, and a Ø5mm (3/16”) hole immediately beside for
the breather tube (as indicated on the template).
Method B
Red shaded areas of template
Drill a Ø25mm (1”) hole at a 2mm (1/16”) off set to the centre
of the push button location (as indicated on the template).
RON-MDT/PBE1-Rev.2. 01-05-18
HOLE
Ø5mm
(3/16’’)
for breather
tube
12mm
(1/2’’)
20mm
(3/4’’)
HOLE
Ø19mm (3/4’’)
ON CENTRE
50mm
(1 15/16’’)
Cover in open position
50mm
(1 15/16’’)
2mm
(1/16’’)
37mm
(1 7/16’’)
3 HOLES
Ø3mm (1/8’’) TYP
25mm
(1’’)
50mm
(1 15/16’’)
HOLE
Ø25mm (1’’)
OFFSET 2mm from
centre of switch
9mm
(3/8’’)
Mounting Dimension Template
Andersen Winches
™
A6 A12 A8 A3 A3
A10