background image

USER MANUAL

3

protection equipment to a user and others in the workshop and a worker 
must wear it if necessary. 
3) Never use any power source but compressed air. 

As this tool is designed and manufactured to operate using air 
pressure that is generated by an air compressor authorized by a safety 

certification  authority,  you  cannot  use  any  kind  of  gas  combustible

 

gases  such  as  oxygen  and  acetylene  except  this.  Otherwise,  it  may 

not only cause mechanical trouble but also malfunction or explosion, 

resulting in infliction of fatal injury on a user or those around him or her. 
4) Use it within the optimum range of air pressure. 
This  tool  is  designed  to  operate  within  a  range  of  pressure  between 
58 psi and 100 psi (or between 4 bar and 7 bar). Connect this tool to a 
pressure controllable device so that you can work under fixed pressure. 

When operating this tool, never use it under pressure of  120psi (8bar) 
and over. This tool can not connected to pressure higher than 120 psi(8 

bar) , or will damage the parts.
5) Don’t use it near inflammables (combustibles). 
Never  operate  this  tool  near  inflammables  (such  as  thinner  and

 

gasoline). Combustible gas from such materials can be sucked into 

a compressor and compressed together with air, possibly resulting in

 

explosion. 

6) Be careful not to aim or fire it toward yourself or any other person in any case.
You should be careful not to aim it toward yourself or any other person 
in any case whether the tool is loaded with fasteners or not. Then, even 
if  malfunction  or  undesired  firing  occurs,  you  can  minimize  damage 
caused by the fired fasteners. Otherwise, it may result in serious injury.
7) Never touch the trigger except when this tool operates for work. 
Never  touch  the  trigger  except  when  air  is  connected  to  this  tool, 
which operates for work. It is especially very dangerous to change the

 

position  or  move  around  during  operation  with  your  finger  fixed

 

on  the  trigger,  and  you  may  not  do  any  similar  action.  Otherwise

 

Possible  carelessness  may  result  in  infliction  of  serious  injury  on  a

 

user or those around him or her. 

Summary of Contents for RA-F30














Reviews: