19
20
M A K I N G A C U P O F C O F F E E
The machine is only compatible with ROMBOUTS 1.2.3 SPRESSO
®
pods.
1 - Fill the tank with fresh water (
6
).
2 - Plug in the power cable (
13
).
3 - The central light (
2
) will display 3 colours (blue, white and red) one after the
other, and then go out. The machine is now on stand-by.
4 - Press coffee button (
3
) or (
4
) to start heating (both coffee buttons flash).
5 - When the machine reaches the required temperature, the two coffee buttons (
3
)
and (
4
) will stay ON steady, and the machine is ready to serve coffee.
6 - Open the coffee pod packaging, remove the lid, and take out the pod.
7 - Pull on the machine handle (
1
) to maximum while lifting to reveal the pod slot.
8 - Insert the pod in the slot and check positioning (the pod must not protrude).
9 - Push the handle (
1
) towards the control buttons until completely closed.
IMPORTANT: It is essential to fully close the handle in order to obtain a great cup
IMPORTANT: It is essential to fully close the handle in order to obtain a great cup
of coffee. This Eco-Responsible machine is not equipped with an automatic closing
of coffee. This Eco-Responsible machine is not equipped with an automatic closing
device to reduce energy consumption, therefore the user must push lightly on the
device to reduce energy consumption, therefore the user must push lightly on the
bent end of the handle with the palm of their hand, to fully close the handle.
bent end of the handle with the palm of their hand, to fully close the handle.
It is easy to know when the required position has been reached, the handle will resist
It is easy to know when the required position has been reached, the handle will resist
closing when approaching closure and then all resistance will disappear when the
closing when approaching closure and then all resistance will disappear when the
handle is in the correct closed position.
handle is in the correct closed position.
However, do not push hard on the
However, do not push hard on the
very end of the handle.
very end of the handle. Excessive
Excessive
pushing forces can indeed be
pushing forces can indeed be
caused by a pod remaining in the
caused by a pod remaining in the
machine from a previous cycle, or
machine from a previous cycle, or
a full pod basket (empty the pod
a full pod basket (empty the pod
basket on a regular basis to avoid
basket on a regular basis to avoid
any damage to your new coffee
any damage to your new coffee
pods for this reason).
pods for this reason).
10 - Press the required button: Small coffee (
3
) or Large coffee (
4
). The light on the
selected button will remain on and the other button will go out. The coffee is on
its way. The coffee cycle stops automatically at the end of the cycle or can be
interrupted manually by pressing the selected button again.
11 - After the coffee pod has brewed, raise the handle as far as possible (
1
) while
pulling towards you, the used pod will then fall into the used pod basket (
7
).
The machine is then ready to make another coffee.
P R O G R A M M I N G
The 2 coffee options (small or large) are pre-programmed by default (4 cl for a small
coffee and 12 cl for a large coffee). You can change these volumes as follows:
1 - Start the machine (see instructions in the above section). The white lights on
the coffee buttons (
3
) and (
4
) must stay ON (the machine is at the right
temperature, ready to make coffee). Check that the water tank (
6
) contains
enough water to enter settings.
2 - Press and hold the coffee button for the volume you wish to change for at least
5 seconds. The white light on the button will then flash rapidly, and the central
indicator (
2
) will light up white. The machine is now in programming mode.
3 - Raise the handle (
1
) and insert a pod.
4 - Lower the handle (
1
) and press the coffee option to be programmed (the button
selected previously, which is now flashing), the central light will go out and the
machine will start to pour the coffee.
5 - Once the required volume of coffee has been poured, press the same button
again to stop serving and save the selected volume.
6 - The white light on the programmed button will then stay ON (together with the
light on the other coffee button), the programming has been saved for the button.
The machine is ready to make coffee.
Note: the factory settings for coffee options can be recovered as follows:
1 - Start the machine (see instructions in the above section). The white light on
the coffee buttons (
3
) and (
4
) must stay ON (the machine is at the right
temperature, ready to make coffee).
2 - Press and hold the coffee button for the volume you wish to change for at least
5 seconds. The white light on the button will then flash rapidly, and the central
indicator (
2
) will light up white. The machine is now in programming mode.
3 - Press and release the other coffee button: the button light will stop flashing,
factory settings are re-established, the two coffee button lights (
3
) and (
4
)
will come ON, and the machine is ready to serve coffee.
