Rolls-Royce Helicon X3 User Manual Download Page 15

Page: 15 / 140

The content of this document is the property of Rolls-Royce plc and may not be redistributed in whole or in part thereof without
express written consent of Rolls-Royce plc.

Doc. No.: 13S000411

Revision: A

System Description

General ......................................................................................................... 3

System Overview ......................................................................................... 3

Design .......................................................................................................... 4

Functions ................................................................................................... 10

4.1 Pitch Control ................................................................................................ 10

4.2 Thruster Azimuth Control ............................................................................. 12

4.3 RPM Control ................................................................................................ 14

4.3.1 RPM Control Electric Drive Motor .................................................... 14
4.3.2 External RPM Control ....................................................................... 14
4.3.3 RPM Order Output ........................................................................... 14
4.3.4 Propeller/Shaft RPM Indication ........................................................ 14

4.4 Command Transfer ...................................................................................... 14

Location of Manufacturing Number ......................................................... 14

5.1 Marking Locations ....................................................................................... 14

5.1.1 Company Identification ..................................................................... 15

Summary of Contents for Helicon X3

















































































































Search results

Summary of Contents for Helicon X3

Reviews:

Related manuals for Helicon X3

Brands by name

Popular brands

Rolls-Royce Helicon X3, User Manual

Search results

Summary of Contents for Helicon X3

Reviews:

Related manuals for Helicon X3

Brands by name

Popular brands