Rolls-Royce Helicon X3 User Manual Download Page 24

Page: 24 / 140

System Description

Page 10 of 16

Doc. No.: 13S000411

Revision: A

1. I/O

modules

2. Capacitors

(optional)

3. Power

distribution

4. Power

distribution

5.  Power / network / CANBus terminals
6.  Local panel connection
7.  Actuator interface card(s) (optional)
8. Relays

(optional)

9. Signal

isolation

amplifiers (optional)

10. I/O terminals

4 Functions

Tunnel Thruster Control Functions

The control functions included in the Tunnel Thruster Control system:
• Pitch control
• Command transfer

Main Propulsion Azimuth Control Functions

The control functions included in the Main Propulsion Azimuth Control system:
• RPM control
• Azimuth control
• Command transfer

4.1

Pitch Control

The function of the pitch controller is to move the propeller blades in accordance to the

control lever order. The actuator unit represents the interface between the remote control

and the main servo system, which performs the actual positioning of the blades.

Summary of Contents for Helicon X3

















































































































Search results

Summary of Contents for Helicon X3

Reviews:

Related manuals for Helicon X3

Brands by name

Popular brands

Rolls-Royce Helicon X3, User Manual

Search results

Summary of Contents for Helicon X3

Reviews:

Related manuals for Helicon X3

Brands by name

Popular brands