background image

Safety information

Important information

1. Please remember that the natural playfulness  and 

    temperament of children may result in unforeseeable 

    situations and dangers, for which the manufacturer 

    cannot be held responsible. You should therefore instruct 

    the children or users of how to use the BMW Vehicle

    correctly, draw their attention to the possible 

    dangers and keep children under supervision at all times.

2. BMW AG cannot accept any liability for accidents of any 

    kind that are the user's own fault or resulting from the

    user's failure to adhere to the following warning instructions.

3. The BMW Vehicle is not approved for road use.

4. It should therefore not be used on public roads, paths or the 

     like.

5. Children must wear closed shoes. Not to be used in traffic.

6. The BMW Vehicle should not be used near stairs or

      sloping land.

7. Nearby stairs must be secured to ensure that they do not

     present any danger to the children.

8. The BMW Vehicle should not be used on icy or slippery

     ground.

9. Do not store the BMW Vehicle close to heat sources.

10. The BMW Vehicle should not be used in water.

11. The BMW Vehicle is only designed to carry a single

        child.

12. Do not attach it to other vehicles.

13. The rider should always wear a helmet that is properly

       fastened .

14. The BMW Vehicle is only suitable for children between

     3 and 5years of age.

15. The maximum payload of the vehicle is 22kg.

16. Store the BMW Vehicle in a secure location. Do not

      leave it outside overnight.

17. Keep small parts that can be swallowed and plastic bags out

       of the reach of children. Danger of suffocation.

18. Before starting assembly, check that all parts are present. If

       any parts are missing, please contact the dealer from which

       you purchased the vehicle.

19. Keep the incompletely assembled vehicle out of the reach of

       children since it may contain sharp edges, pointed corners 

       and small parts.

20. Please retain all packaging for further information. This toy is

       not suitable for children under 3 years of age due to small

      parts.

21. Do not activate the vehicle unless you are seated and in a safe, 

       outdoor environment suitable for riding. There are additional

       hazards of using the toy in areas other than private grounds.

22. The toy shall be used with caution since skill is required to

       avoid falls or collisions causing injury to the user and third

       parties. Continuous adult supervision required; never use

       near motor vehicles; never use near streets, swimming pools,

       hills, steps, or sloped driveways.

23. Adult Assembly required.

24. Never allow more than one rider.

Care and maintenance

The wheel bushings and drive shaft should be 

lubricated with a few drops of oil four times a 

year.

Check all the parts at regular intervals for signs of 

wear. Check the screw connections for a secure 

fit. To maintain the high safety level, worn parts 

must be replaced immediately and the vehicle 

not used until it has been repaired.

You can obtain spare parts from Hunter products.

WARNING

Assembly

1.Assemble Rear Wheel:(fig1)

Insert the rear wheel axle into the chassis and insert the left 

rear wheel, washer, hexagon nut into the rear axle in the order 

shown. Then, cover the rear wheel hubcap. Follow the same 

procedures to assemble the right rear wheel.

2.Assemble Pedal Component:(fig2)

Connect the left side pedal into the left square hole of the front 

wheel and insert the right side pedal into the right square hole 

of the front wheel. 

3.Assemble front fork:(fig3)

Insert the right and left leg of front fork (the mudguard should 

face forward) into the connected hole ,please pay attention that 

the hole of two sides must be in alignment. Use ST4.2*29

self tapping screw to tighten the connecting part and hole 

closely(the tighten torque is 1.5 N-m),and then fix the mudguard 

and front fork connecting part with ST3.2*13 self tapping screw 

for fastening. (the tighten torque is 1.5N-m).

4.Assemble front wheel component:(fig4)

Insert the stand pipe of front fork (the mudguard should face 

forward) into the fixing hole in front of the chassis.

5.Assemble handle bar:(fig5)

Remove the M5*28 screw from the handle bar component first 

and insert the stand pipe of the handle bar into the stand 

pipe(pay attention to the assemble direction of the handle bar), 

use M5*28 screw for fastening(the tighten torque is 2.5N-m).

6.Using the seat:(fig6) 

Rotate the button on the seat to the open position, the seat can 

be upturned and the following space under the seat also can be 

used as a storage box.

Reviews: