background image

| Automate Programming Instructions | AC Tubular Motors 

ROLLEASE ACMEDA

P1 Press  

Condition

Function Achieved

Visual 

Feedback

Audible 

Feedback

Function Described

Short Press

If limit is NOT 

set

None

No Action

None

No Action

 

If limits are set

Operational control 

of motor, run to limit. 

Stop if running

 

Motor runs

 

None

Operational control 

of motor after pairing 

and limit setting is 

completed first time

If motor is in 

“Sleep Mode” & 

limits are set

 

Wake and control

Motor wakes 

and runs in a 

direction

 

None

Motor is restored from 

Sleep Mode and RF 

control is active

3.1  Motor state test

P1 BUTTON FUNCTIONS

Hold 

P1

P1

Activate Pairing Mode

Sleep Mode

Reverse Direction

Reset To Factory Settings

Motor Response

Motor Response

Motor Response

Motor Response

Approx.

Approx.

Approx.

Approx.

NOTE

Reverse motor direction from 

P1

 button only when 

motor does not have any limits.

This table  describes the function of a short 

P1

 button press/release (<2 seconds) depending on current 

motor configuration.   

The 

P1

 Button is utilized to administer motor configuration as described below and beginning in Section 

Summary of Contents for Automate I E

















Reviews: