background image

15 

| Automate Programming Instructions | AC Tubular Motors 

ROLLEASE ACMEDA

10  TROUBLESHOOTING

 Problem

Cause

Remedy

Motor is not responding

A/C power supply not plugged in.

Check motor to power cable 

connection and AC plug.

Transmitter battery is discharged

Replace battery

Radio interference/shielding

Ensure transmitter is positioned 

away from metal objects and the 

aerial on motor or receiver is kept 

straight and away from metal

Receiver distance is too far from 

transmitter

Move transmitter to a closer 

position

Power failure

Check power supply to motor is 

connected and active

Incorrect wiring

Check that wiring is connected 

correctly (refer to motor 

installation instructions)

Cannot program a single Motor 

(multiple motors respond)

Multiple motors are paired to the 

same channel.

 Always reserve an individual 

channel for programming 

functions
SYSTEM BEST PRACTICE - Provide 

an extra 15 channel controller in 

your multi motor projects, that 

provides individual control for each 

motor for programming purposes
Place all other motors into sleep 

mode (ref to 

P1

 button function 

overview - Section 3)

Summary of Contents for Automate I E

















Reviews: