manualshive.com logo in svg

Roland XC-540MT, Manual To Installing

Share
Download
Roland XC-540MT Manual To Installing Download Page 41

3-2  Starting the Print Operation

Chapter 3  Printing

39

Chapter 3  Printing

Click 

, configure the settings in [Quality-

Settings] and [Color Management].

 P. 22, “3-1 Print Job Setting”

Click [OK].

  Click  [Media]  and  then  [Metallic  Color 

Chart].

 Check the page size.

If the size of the media loaded on the printer is not 
adequate for the page size, change it to another 
media of sufficient size.

 Click [OK].

The print job of the Metallic Color Chart is added to 
the job list.

Click 

.

Printing will be started.

When printing a Metallic Color Chart, the [Quality] settings from the [Queue Properties] window are 
always applied. Since you cannot change the quality settings for the job using the [Job Settings] 
window after it has been added, be sure to configure the settings in the [Queue Properties] window 
before performing the following operations.

Summary of Contents for XC-540MT









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands