background image

 

5

 

IMPORTANT NOTES

 

291b

 

In addition to the items listed under “IMPORTANT SAFETY INSTRUCTIONS” and “USING THE UNIT SAFELY” on pages 2 
and 3–4, please read and observe the following:

 

This unit is equipped with a protection circuit. The protection circuit helps ensure safety by operating when excessive input 
continues for a long time while the device is at a location with a high ambient temperature. Sound drop-out may occur when 
the protection circuit is actuated during use. Please read through the documentation carefully to ensure correct use.

 

Power Supply

 

301

 

• Do not use this unit on the same power circuit with any device that will generate line noise (such as an electric motor or 

variable lighting system).

 

307

 

• Before connecting this unit to other devices, turn off the power to all units. This will help prevent malfunctions and/or damage 

to speakers or other devices.

 

Placement

 

351

 

• Using the unit near power amplifiers (or other equipment containing large power transformers) may induce hum. To alleviate 

the problem, change the orientation of this unit; or move it farther away from the source of interference.

 

352a

 

• This device may interfere with radio and television reception. Do not use this device in the vicinity of such receivers.

 

352b

 

• Noise may be produced if wireless communications devices, such as cell phones, are operated in the vicinity of this unit. Such 

noise could occur when receiving or initiating a call, or while conversing. Should you experience such problems, you should 
relocate such wireless devices so they are at a greater distance from this unit, or switch them off.

 

354b

 

• Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise 

subject it to temperature extremes. Also, do not allow lighting devices that normally are used while their light source is very 
close to the unit (such as a piano light), or powerful spotlights to shine upon the same area of the unit for extended periods of 
time. Excessive heat can deform or discolor the unit.

 

355

 

• To avoid possible breakdown, do not use the unit in a wet area, such as an area exposed to rain or other moisture.

 

356

 

• Do not allow rubber, vinyl, or similar materials to remain on the unit for long periods of time. Such objects can discolor or 

otherwise harmfully affect the finish.

 

357

 

• Do not put anything that contains water (e.g., flower vases) on the unit. Also, avoid the use of insecticides, perfumes, alcohol, 

nail polish, spray cans, etc., near the unit. Swiftly wipe away any liquid that spills on the unit using a dry, soft cloth.

 

359

 

• Do not paste stickers, decals, or the like to this instrument. Peeling such matter off the instrument may damage the exterior 

finish.

 

Maintenance

 

401a

 

• For everyday cleaning wipe the unit with a soft, dry cloth or one that has been slightly dampened with water. To remove 

stubborn dirt, use a cloth impregnated with a mild, non-abrasive detergent. Afterwards, be sure to wipe the unit thoroughly 
with a soft, dry cloth.

 

402

 

• Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation.

Summary of Contents for VGA-3





































Reviews: