14
Connections with other R-BUS devices
VM-3100Pro Quick Setup
By using Quick Setup, you can instantly recall settings for
use with a connected RPC-1. At this time, settings for
remotely controlling your sequencer software will also be
recalled. The following types of Quick Setup are available.
When you perform one of the above operations, the display
will ask
“Load xxxx Configuration?”
(xxxx is either
LOGIC
,
CAKEWALK
, or
CUBASE
). Press
[ENTER/YES]
.
When
Quick Setup
is executed, the following parameters and
routings will be changed.
Connections with the VM-7200/7100
In order to connect the VM-7200/7100 with the RPC-1, the
VM-24E I/O expansion board
(an expansion board that adds
an R-BUS connector) must be installed in the VM-7200/7100.
Updating the system program
In order for the VM-7200/7100 to be connected and used
with the RPC-1, system program
version 1.60 or later
is
required.If your VM-7200/7100 has
version 1.50 or earlier
,
you must update the system program.
Checking the version
After starting up the VM-7200/7100 system, press
[on Display]
and
[9]
.
Unit 1/2 Version
is the version of the
VM-7200/7100.
Updating the system program
The directory
“UPDATE > VM-7000”
in the included
“Drivers/Update” CD-ROM
contains the data for the update.
Perform the update procedure as directed by the
“readme.doc”
file.
Example settings
RPC-1 settings (in the Control Panel)
•
Master Clock
: Int. Clock
•
Int. Clock Sample Rate
: either 32, 44.1, or 48 kHz
VM-C7200/7100 settings
•
WORD CLOCK SOURCE
: MULTI 1-8
Use the VM-7200/7100
patchbay
to assign the inputs of the
VM-7200/7100 to the RPC-1.
The output of the RPC-1 will be input to
MULTI-IN
. You can
also use multiple RPC-1 units simultaneously. For details
refer to
p. 17 “Using multiple RPC-1 units.”
Software to be controlled
Setting method
Logic Audio
[SHIFT]
+
[F1]
Cakewalk
[SHIFT]
+
[F2]
Cubase VST
[SHIFT]
+
[F3]
Parameter
Value set
Location
Explanation
M.clk Select
RMDB-2
[Shift] + [Digital
in]
Set as slave of
RPC-1
Master Source
MIX
Master [Select]
VM-3100Pro moni-
tors the signal sent
to the RPC-1
LocatorType
MEASURE
[System]
Use locator to trans-
mit SPP
Control Type
Off
[System]
→
[F1-F4]
→
[MIDI]
Don’t transmit Audio
fader values
Timing Mon.
MEASURE
[System]
→
[F1-F4]
→
[MIDI]
Measure is received
as timing data
Beat
4/4
[System]
→
[F1-F4]
→
[MIDI]
4/4 time signature
R-BUS Target
RPC-1
[System]
→
[F1-F4]
→
[MIDI]
Connect with RPC-1
Transport
USER1
[System]
→
[F1-F4]
→
[MIDI]
Transmit USER1
note
ShiftKey
OFF or C-1
[System]
→
[F1-F4]
→
[MIDI]
OFF for Logic. Oth-
erwise, C-1
USER1
Settings for
each program
[System]
→
[F1-F4]
→
[MIDI]
→
[F1-F4]
Overwrite to USER1
EZR SEL
RMDB DIRECT
[EZ Routing]
Send Input 1–8 to
R-BUS
